1. Products
  2. 20 Second Voice Recorder/Playback Module (A93010)

20 Second Voice Recorder/Playback Module (A93010)

$ 5.95 5.95 USD

$ 5.95

Add to Cart

SKU : A96010
Quantity on Hand : 98
Skill Level : Assembled and Tested
ROHS Compliant

Buy 10, Get 5% Off!
Buy 100, Get 10% Off!
MD930100

30-day money-back guarantee
Free Shipping in the U.S. on Orders over $50
Buy now and choose from several shipping methods

0

      CLOSEOUT ITEM. NEW LOW PRICE! LIMITED QUANTITY AVAILABLE.

      PLEASE NOTE: This module, part# A96010, is actually an A93010. It is virtually identical to the A96010 and it operates the same, but downloadable datasheets are available for each for comparison if necessary. The small size is because the IC is in Chip-on-board form. One button is pushed down to record the message through the on-board electret microphone; A LED turns on during this time. The other button just has to be momentarily pressed to replay the message. A second momentary press during playback will stop the playback. Sampling rate is 4K. All you have to add is the speaker (not included) and 5V DC power (not included). We also have an A96010-kit which in addition to the part# A96010 also includes a speaker and two cable connectors to connect the unit to a power supply (not included) and the speaker. The record/play time is determined by the 52K resistor. If you change it to 89K you will get 30 seconds but at a reduced sampling rate.
      Operating voltage: 5 to 6 VDC
      Operating current: 25mA.
      Standby current: 10 uA.
      Size: 34 x 23 x 11 mm.

      The module comes supplied as you see it in the photo. 

      OPTIONAL ITEMS (Not included):
      • 2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
      • 1 x (PB244) Speaker
      • 1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.

      NOTE: This unit will power a 1 watt speaker as is. You do not need to add an external amplifier. However, you can add an external amplifier if you want to drive more than a 1 watt speaker, as long as you follow one of the 2 options below.

      HOW TO ADD AN EXTERNAL AMPLIFIER:

       
      METHOD 1: (Best Option)

      Odoo CMS - a big picture
      Odoo CMS - a big picture


      METHOD 2: (Alternate Option)

      Use this schematic to add a potentiometer when using an additional external amplifier:

      When using an external amplifier, you'll need a potentiometer to decrease the high output signal from the A96010 enough to get a clear sound.

      Odoo CMS - a big picture
       
      Documentation and Downloads

      0 comment

      Leave a comment

      You must be logged in to post a comment.

      Alternative Products:

      10 Sec Recording Module in White Case with 3 Section Slide Switch
      20 Second Recording Module with 9V Battery Connector
      A96010 Kit (20 second Recording Module with Wires and Speaker Included)
      Greeting Card Recording Module 20 Second
      Speaker Round 3 inch 8 ohm 1 watt
      40mm (1.6in) Metal Housing Mylar Speaker 0.25W
      5" Indoor / Outdoor Horn
      Extended record / playback module (8 minutes) (kit)
      TDA7052 Amplifier Module 1W (Kit)
      120 Second Non-Volatile Multi Message Recorder (Kit)
      Audio Amplifier 1W (LM386) (Kit)
      Audio to Light Modulator (Kit)
      BOSS BRS35 3-1/2" Dual Cone Replacement Speaker
      2pin connector cable (8 inch)
      KC7786 PIR Sensor Module 12v (3pin .1in)
      40 Second Voice Recorder/Playback Module (A93010A)