Register | Log In
 
Security > Sensors > 
Your Cart is Empty
View Cart
 
 
Sensors
KC7786 PIR Sensor Module 12v (3pin .1in)
Click here for detailed specs.
Description: This is a fully assembled and tested miniature PIR module (KC7786 with KC778B COB IC) with only 3 connections: Power, Ground & Output (3 pin terminal of standard 0.1 inch pitch). Rated for 12VDC input power. Uses RE200B PIR sensor. Output is an active high pulse of approx. 0.5 seconds and remains active as long as there is motion. Range up to 10 feet. PCB size: 27mm x 27mm
Read More
  Component or Part  
  BB043  
  59  
Quantity:  

Fresnel lens only (for KC7786)
Click here for another picture.
(BB052) Fresnel Lens ONLY.
Read More
  Component or Part  
  BB052  
  432  
Quantity:  

KC7783R PIR Detector Module (Low cost version) (Assembled and tested)
Click here for detailed specs.
Mechanical and electrical specs is the same as the KC7783 except for a lower cost IC (KC778B IC) package used in this KC7783R.


RoHS Compliant: YES.
Read More
  Component or Part  
  BB054  
  799  
Quantity:  

KC778B Pir Controller Chip SOP
tn_bb055.jpg
KC778B Pir Controller Chip SOP

Download Datasheet here:
http://www.electronics123.com/s.nl/it.A/id.74/.f
Read More
  Component or Part  
  BB055  
  391  
Quantity:  

RE200B-P Pyroelectric Infrared Sensor
Click here for detailed specs.
RE200B-P Pyroelectric Infrared Sensor
Read More
  Component or Part  
  BB083  
  507  
Quantity:  

KC7783 PIR Detector Module (Assem and tested)
Click here for specs, downloads, and more pictures.
This is a fully assembled and tested miniature PIR module (KC7783 with KC778B IC) with only 3 connections: Power, Ground & Output. Rated for 4 - 12VDC input power. Uses RE200B PIR sensor. Output is an active high pulse of approx. 0.5 seconds and remains active as long as there is motion. Range up to 10 feet. PCB size: 35mm x 25mm.
Read More
  Component or Part  
  CPS76  
  937  
Quantity:  

Door-reed switch and magnet (NO)
tn_mb163.jpg
A surface mounting reed switch and magnet in similar white plastic moldings. Contacts are NO (normally open) when the reed switch and magnet are in close proximity to each other. Can be used to activate an alarm system when a door is opened. Attached to surface by either double-sided tape or screws (not included).

Specifications:
  • Operating Gap (for open switch contacts): 0 to 18mm (between the magnet and reed switch that are mounted onto non-metallic surfaces)
  • Reed Switch Contact Rating: max. 250mA / 30V
  • Dimensions (both parts): 55 x 12 x 13mm.
  • Fixing centers: 54.5mm using M3 screws. (MB163)
Read More
  Component or Part  
  MB163  
  6  
Quantity:  

Door-reed switch and magnet (NC)
tn_mb049.jpg
A surface mounting reed switch and magnet in similar white plastic moldings. Contacts are NC (normally closed) when the reed switch and magnet are in close proximity to each other. This is the preferred configuration for security systems. Can be used to activate an alarm system when a door is opened. Attached to surfaces by either double-sided tape or screws (not included).

Specifications:
  • Operating Gap (for Closed Switch Contacts): 0 to 18mm (between the magnet and reed switch that are mounted onto non-metallic surfaces)
  • Reed Switch Contact Rating: max. 500mA / 100V
  • Dimensions (both parts): 55 x 12 x 13mm.
  • Fixing centers: 54.5mm using M3 screws. (MB049)
Read More
  Component or Part  
  MB049  
  21  
Quantity:  

Twin Photo Beam Detectors, 60m
tn_pem300d.jpg
Features:
  • Easy and accurate adjustment thanks to the built-in laser
  • Range:
  • Outdoor: 30m (100ft)
  • Indoor: 60m (200ft)
Specifications:
  • Power supply: DC 10 ~ 30V (not incl.)
  • Detection system: simultaneous breaking of 2 beams
  • Response time: 50ms ~ 700ms (variable)
  • Alarm output: NC/NO 1A/120VAC
  • Tamper output: NC 1A/120VAC
  • LED indicators:
  • Alarm LED (receiver): red LED on - when transmitter and receiver are not aligned or when beam is broken
  • Signal LED (receiver): yellow LED on - when receiver's signal is weak or when beam is broken
  • Power LED (transmitter & receiver): green LED on - indicates that device is ON
  • Wave length: 650nm
  • Laser output power: max. 5mW
  • IP rating: IP55
  • Alignment range:
  • Horizontal: ± 90°
  • Vertical: ± 15°C
  • Operating temperature: -13°F to +131°F
  • Dimensions: 6.7" x 3.0" x 2.8"
Read More
  Assembled and Tested  
  PEM300D  
  2  
Quantity:  

MINI INFRARED SECURITY SYSTEM, 7m
tn_pem7d.jpg
Features:

easy to install
adjustable timer & volume
applications:
  entry detection
  automatic alarm warning
  present detection
includes:
  1 x retro-reflection IR photoelectric beam sensor
  1 x power supply 120VAC / 9V DC / 200mA
  1 x alarm speaker (timer & volume adjustable)
optional counter for PEM7D: PEM7D/C
 

Specifications:

nominal detection range: 23ft
light source: IR LED
speaker:
  power supply: DC 9V
  speaker output: chime / off / alarm (selection through by switch)
  duration audio signal: about 1 sec. for chime, 30 sec. for alarm
  timer adjustable: 3 - 30sec. before alarm activation
  volume adjustable: yes (from 0 to max)
working temperature: -4°F to +122°F
power supply: DC 9-15V regulated (adapter included)
total current consumption: < 100mA
standby current: 25mA
(PEM7D)
Read More
  Assembled and Tested  
  PEM7D  
  3  
Quantity:  

Fresnel lens only (As found on the KC7783 & KC7783R)
Click here for detailed specs.
(BB194)
Read More
  Component or Part  
  BB194  
  17  
Quantity:  

OPTICAL SENSOR
acnt.gif
Features:
optical sensor for gate, door, automatic control
durable stainless steel plate
infrared technology
waterproof (IP44 )
(ACNT)
Read More
  Assembled and Tested  
  ACNT  
  1  
Quantity:  

KC7789M PIR Sensor Module with lens -F
Click here for detailed specs and larger picture.
KC7789M is a very small size PIR sensor module with built-in amplifier and logic circuit. The heart of the module is highly reliable PIR controller KC778B. The PIR sensor can be manufacturer specified. The detection angle and distance dependence on the lens used.

PLEASE NOTE: Cap Fresnel lens version F included.

Features:
  • Ultra small size for unlimited application
  • Built-in amplifier to provide TTL output signal
  • High sensitivity with special noise cancellation design
  • High immunity to RFI and line noise
  • Signal will not output within 25 sec when power up
  • Signal output is 0.5sec min
  • Low operation current
  • 3-wire cable of 70mm
Read More
  Assembled and Tested  
  KC7789M-F  
  15  
Quantity:  

KC7789M PIR Sensor Module with Lens -C
Click here for detailed specs and larger picture.
Description: KC7789M is a very small size PIR sensor module with built-in amplifier and logic circuit. The heart of the module is highly reliable PIR controller KC778B. The PIR sensor can be manufacturer specified. The detection angle and distance dependence on the lens used.

PLEASE NOTE:
Cap Fresnel lens version C included.

Features:
  • Ultra small size for unlimited application
  • Built-in amplifier to provide TTL output signal
  • High sensitivity with special noise cancellation design
  • High immunity to RFI and line noise
  • Signal will not output within 25 sec when power up
  • Signal output is 0.5sec min
  • Low operation current
  • 3-wire cable of 70mm
Read More
  Assembled and Tested  
  KC7789M-C  
  2  
Quantity:  

OV10620 CMOS Camera Chip sensor
tn_ov10620.jpg
OV10620 CMOS Camera Chip sensor

Download data sheet here: http://www.electronics123.com/s.nl/it.A/id.3018/.f
Read More
  Component or Part  
  OV10620  
  6  
Quantity:  

REED SWITCH FOR ALARM
Click here for larger pictures.
Specifications:
  • standard type magnetic switch: NO & NC
  • housing: white ABS
  • mounting with screws or double-sided tape
  • contact rating: DC 100V / 0.5A
  • operating gap: 1.2" max.
  • dimensions: 2.5" x 0.5" x 0.5"
Read More
  Component or Part  
  HAA27  
  2  
Quantity:  

SPD61 PIR sensor module (high/low output)
Click here for specs, downloads, and more pictures.
This is a fully assembled and tested miniature PIR module. Compact and complete, easy to use PIR Sensor Module for human body detection. Incorporating a Fresnel lens and motion detection IC, suitable for a wide range of supply voltages and with low current drain. Adjustable delay time with high sensitivity and low noise. Output can be standard TTL output signal (high/low output)
Read More
  Component or Part  
  SPD61-HL  
  62  
Quantity:  

Mini PIR Motion Detector - Build In
Click here for specs, downloads, and more pictures.
Features:
  • With automatic day/night identification
  • Light sensitivity and ON-time adjustable
  • For building-in

Specifications:

  • Detection angle: 100°
  • Detection range: 26 ft.
  • Rated load: load, 150W fluorescent load (120V)
  • Power supply: 120V/50-60Hz
  • Working temperature: 14°F~104 °F
  • Working humidity: <93%RH
  • Time-delay switch: 5 s, 30 s, 1 min, 3 min, 5 min, 8 min
  • Light control: < 3 Lux to 2000 Lux
  • Dimensions:
  • Visible part: Ø55/64" x 25/64"
  • Hidden part (controller): 2 11/64" x 1" x 1 3/8"
  • Weight: 1.44 oz.
Read More
  Component or Part  
  PIR415U  
  11  
Quantity:  

4.5V PIR with Adjustable Sensitivity
Click here for specs, downloads, and more pictures.
Description: This is the PIR that is used with our USB6M+PIR module. It has an adjustable sensitivity and it's dimensions are: 35mm x 28mm. PIR range is approximately 9 - 13 feet.

NOTE: This is the PIR sensor module ONLY.
Read More
  Assembled and Tested  
  6MPIR  
  485  
Quantity:  

FlyCamOne eco V2
Click here for more pictures, software, etc...
Description: Do you ever wonder what your autonomous robots do all day? Or have you ever wanted to put yourself in the driver's seat of your favorite RC car? Maybe you just want to add a security camera to your desk at work to see who's stealing your pens. Well thanks to the FlyCamOne eco, recording video is so easy and affordable that you could get a camera for each of those situations.

The FlyCamOne eco is a self-contained module that records 720x480 color video at 30 fps with sound! Not only that, but it can snap pictures as well. Simply plug in a Li-Poly battery, insert a Micro SD card and select the mode using the on-board push-button. If your application is remote controlled, the module can also be powered and controlled from an open channel on your RC receiver.

The camera itself is mounted on a swivel head and attached by a ribbon cable, allowing it to be mounted external to your project while keeping the control board out of harm's way. There's even a mode to flip the video 180 degrees so you can mount the camera up-side down.

Navigating through the modes using the bi-color LED on the board can be a little confusing at first because the guide printed on the sticker seems to have "ready" and "record" backwards. When the light is green, you're on standby, when it's red, you're recording. 
Read more...

Weight: 15g

Dimensions:
  • Control Board: 30x57x7mm
  • Camera Head: 22x24x28mm
  • Ribbon Cable: 100mm
  • RC Cable: 225mm
Features:
  • Supports up to 8GB Micro SD card
  • Color Video, Picture and Picture Burst Modes
  • Resolution: 720 x 480px @ 30 fps
  • Voltage: 3.7V Li-Poly or 4.5 - 6V RC Receiver
  • SD Card Accessible via On-Board Mini-USB
  • On-Board Microphone and Status LED
  • Read more...
Read More
  Assembled and Tested  
  SEN11171  
  2  
Quantity:  

SPD61 PIR sensor module (open collector output)
Click here for specs, downloads, and more pictures.
This is a fully assembled and tested miniature PIR module. Compact and complete, easy to use PIR Sensor Module for human body detection. Incorporating a Fresnel lens and motion detection IC, suitable for a wide range of supply voltages and with low current drain. Adjustable delay time with high sensitivity and low noise. (Open Collector Output)
Read More
  Component or Part  
  SPD61-OC  
  94  
Quantity: