One Chip AM Radio

Shopping Cart

	Your Cart is Empty
	View Cart

One Chip AM Radio

Documentation in acrobat format (K63)

Complete AM radio on a PCB. Tuned radio frequency front-end, single chip RF amplifier & detector and two stages of amplification of the audio signal into a speaker. All components supplied. Coil prewound. Excellent for schools.(CPS63)

Quantity	Price
1 – 9	$14.25
10 – 99	$13.50
100 +	$12.38

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS63
Quantity Available:		5

Tell a Friend

You might also consider these items:

Stereo Preamplifier - Tone Control Unit

This is a preamplifier and tone control unit
which will make a useful addition to any
of our power amplifier kits. It is extremely
easy to construct due to the use of a special IC,
the Philips TDA 1524A. This contains all the
circuitry required to provide up to 20 dB of
voltage gain, +/-15 dB of bass and treble
control, channel balance, and a switchable
loudness contour.
Specification
D.C. Input : 15V DC supply or 12V DC battery. 50 mA min.
Maximum output : > 3 V RMS
Maximum input : > 300 mV, G = 20 dB
> 3V RMS, G = 0dB. Input Z > 10 k ohm. Output Z < 300 ohm
Frequency resp. : < 10 Hz to > 50 kHz + / – 1 dB
THD at 1kHz : < 0.1 % at 1V output
S/N ratio : > 80 dB, G = 0 dB
Bass boost/cut ~ 15 dB at 50 Hz
Treble boost/cut ~ 15 dB at 15 kHz
PCB size: 4 inches x 2 1/4 inches. (CPS100)

Quantity	Price
1 – 9	$20.35
10 – 99	$18.90
100 +	$18.27

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS100
Quantity Available:		5

Electronic Music Box Engine

This kit is the electronic equivalent of a mechanical music box. Tunes are contained in an IC. Tunes are started by light falling on an LDR. Two music IC's provided. 8ohm 1 watt speaker included. PCB size: 43mm x 34mm (1.69inch x 1.34inch)
Power supply: 3VDC (CPS104)

Quantity	Price
1 – 9	$14.82
10 – 99	$14.04
100 +	$12.87

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS104
Quantity Available:		9

MK484 am-radio IC (TO92)

(BB044)

Quantity	Price
1 – 9	$1.54
10 – 99	$1.30
100 +	$1.17

Skill Level of Item:		(Component or Part)
Product #		BB044
Quantity Available:		27

USB PIC Programmer (Assembled) (Zif socket included)

This programmer connects to a USB port. On board 'B' USB connector. Free software. A wide-slot 40 pin ZIF socket is included with this assembled version. Power supply: at least 16VDC (18VDC preferred) center positive required (power supply jack 5.5mm OD 2.5mm ID) at least 200mA. See this page for which devices can be programmed. (CPA150)

Quantity	Price
1 – 9	$77.52
10 – 99	$72.00
100 +	$69.60

Skill Level of Item:		(Assembled and Tested)
Product #		CPA150
Quantity Available:		13

Toy motor kit

Construct a working DC Motor. This clever kit has been delighting children for decades. All parts provided, including: 2 coils of copper wire; base; field pole; armature core; brushes; all fasteners. Instruction booklet with theory and experiments included.
Operates on 3 to 6 volt batteries (not included). (CPN135S)

Quantity	Price
1 – 9	$5.45
10 – 99	$5.25
100 +	$4.95

Skill Level of Item:		(Kit - No Soldering Required)
Product #		CPN135S
Quantity Available:		61

Touch/Contact Switch

Both types of switches are built onto the one PCB so you can see and explore how each type works. A battery can power the touch switch (2 contacts) but a power supply (like CPS4) must be used for the touch plate (1 terminal) to work. High quality 12V relay rated at switching 240V/3A supplied. Uses 14011 IC. (CPS10)

Quantity	Price
1 – 9	$7.98
10 – 99	$7.56
100 +	$6.93

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS10
Quantity Available:		7

18W BTL Audio Power Amplifier

This kit contains the essential components to build a low voltage, high power mono 18W Bridge Tied Load (BTL) amplifier module using the Hitachi HA13118. The circuit is straight out of the data sheet. Only a few external passive components are required to make the module. The IC contains surge protection circuits and thermal shutdown circuits. The speaker and cables are not included. (CPS105)

Quantity	Price
1 – 9	$14.25
10 – 99	$13.50
100 +	$12.38

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS105
Quantity Available:		14

(Not Pictured)

60/160 AM tuning cap

(BB084)

Quantity	Price
1 – 9	$0.56
10 – 99	$0.52
100 +	$0.49

Skill Level of Item:		(Component or Part)
Product #		BB084
Quantity Available:		146

50W amplifier module TDA7294

The heart of this amplifier module is a monolithic integrated circuit from SGS-Thomson, TDA7294. It is intended for use as an audio class AB amplifier in hi-fi applications. It has a wide voltage range and output current capability, enabling it to supply the highest power into both 4 Ohm and 8 Ohm loads. With the addition of a handful of parts and a suitable power supply, this module will deliver > 50W RMS into 8 Ohm @ 0.1% THD. HEATSINK NOT INCLUDED. User must supply a heatsink rated at 1.4 deg C/W.

Specifications (± 35V D.C. power supply)
Output power : > 50W RMS, 4-8 Ω load
~ 80W into 4Ω max.
~ 60W into 8Ω max.
Gain: 24 dB (30dB modification)
Input sensitivity : 1.3V for 50W, 8 ohm
0.9V for 50W, 4 ohm
(0.6V, 50W, 8Ω, G=30dB)
Input impedance : 10kΩ
Signal-to-Noise ratio : > 95 dB, (>105 dBA)
Frequency response : ~ 20Hz - 200kHz, –3 dB
Slew rate : > 10V/uS
THD : < 0.01%, 1W-40W,1kHz
< 0.1%, at 50W, 20-20kHz
IMD : < 0.01%, 1W

(CPS106)

Quantity	Price
1 – 9	$30.52
10 – 99	$28.35
100 +	$27.41

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS106
Quantity Available:		5