Relay Board for 2 x 1A Miniature Relays

Shopping Cart

	Your Cart is Empty
	View Cart

(K45)

Quite often the hobbyist needs to use a relay. For example the output of a PIR has output pads for the alarm signal which must be connected to a remote switching device. To fill needs like these we have two kits which are just a relay, PCB and terminal blocks for the input/output signals. There are many relay pin-outs & drive voltages to select from. We have standardized on two 12V relays from Goodsky Relay Board for 2 x 1A Miniature Relays(CPS45)

Quantity	Price
1 – 99	$10.83
100 +	$9.41

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS45
Quantity Available:		11

Tell a Friend

You might also consider these items:

Dual HI / LO Switching Relay Board

The kit is based around the ULN2003A IC, a 7-channel high voltage, high current relay driver. The inputs are TTL compatible so they can be connected to 5V. LO 0-0.8VDC. HI 2.4V - 12VDC. Operating voltage: 12V DC. The relay will be operated when either the LO input is low (0 – 0.8V) or the HI input is high (2.4V – 12V.). Two 12V relays, coil resistance 400 ohm are used. It is rated to switch 250VAC at 12A. However, because of the PCB track thickness and width we do not recommend using the relay to switch more than 5A. PCB size: 2 3/4"x1 3/4" (CPS156)

Quantity	Price
1 – 9	$12.54
10 – 99	$11.88
100 +	$10.89

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS156
Quantity Available:		19

..........................

Relay Board for 5/10A Relay

Relay Board for 5/10A Relay(CPS43)

Quantity	Price
1 – 9	$10.83
10 – 99	$10.26
100 +	$9.41

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS43
Quantity Available:		17

..........................

Power supply voltage adj. 1.5 to 30V kit

This is a basic adjustable voltage power supply using the popular three pin regulator, LM317T. You can select any voltage between 1.5V and 30V using a potentiometer. The LM317T is rated at 1.5A so you must use a larger heat sink when drawing high currents. Unregulated AC or DC input via terminal block or power jack. Requires a suitable transformer.(CPS68)

Quantity	Price
1 – 9	$12.54
10 – 99	$11.88
100 +	$10.89

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS68
Quantity Available:		15

..........................

Voice Recording Module 2 x 20sec sections

The A96020 voice recording module offers true single chip solid state storage capability and requires no software or micro-controller support. It provides high quality recording and playback with dual 20 second message. Sampling rate is 3.2K. Size: 34 x 23 x 11 mm. All you need to do is add a speaker (not included) and 5V DC Power (not included). Features - Non volatile flash memory technology - No battery back up required - User friendly, easy to operate - Slide switch for record or play back - Separate key to trigger message 1 or 2 - Low power consumption - LED to indicate recording and playback - Built-in condenser mic - Automatic power down - 5-6V Operation.

OPTIONAL ITEMS (Not included):
2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
1 x (PB244) Speaker
1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.

(A96020)

Quantity	Price
1 – 9	$8.89
10 – 99	$8.42
100 – 999	$7.72
1000 +	$4.95

Skill Level of Item:		(Assembled and Tested)
Product #		A96020
Quantity Available:		73

..........................

50 second USB recording module (Out of Stock)

This module plugs directly into the USB port of your PC. Then use the free software to record up to 50 seconds of mp3 or wav file to this module. Comes with batteries and speaker ready for use.

Features
Up to 50 seconds of re-recordable voice message (8K sample rate)
Use USB type-A male connector for direct plug into USB port of PC (USB1.1)
Easy to transfer software for windows of MP3 or WAV audio file.
Choice of 8K or 12K sample rate.
50 seconds non-volatile recordable IC.
Operating Voltage 4.5V (3 x AG10 batteries included)
Operating Current < 50 mA
Standby Current < 5 uA
Push switch for playback / stop
Speaker 40mm metal housing mylar speaker (included)

Dimensions:
Main board: Excluding USB connector: 1.7" x 1.13"
Including USB connector: 2.25" x 1.13"
Battery board: 2.25" x 0.8"
speaker: 1.6" (diameter)

CURRENTLY OUT OF STOCK. NEW STOCK TO ARRIVE AT END OF SEPTEMBER.

Quantity	Price
1 – 9	$11.95
10 – 99	$10.50
100 – 999	$9.71
1000 +	$8.95

Skill Level of Item:		(Assembled and Tested)
Product #		USB2M
Quantity Available:		0