TDA7052 Amplifier Module 1W

Shopping Cart

	Your Cart is Empty
	View Cart

Documentation in acrobat format

A 1W power amplifier building block designed to be part of a larger project. Ideal as a low power battery operated amplifier (from 3 to 15V) driving an 8 ohm speaker. The Philips TDA7052 is a general purpose amplifier. No heatsink needed. Short circuit protected. PCB size: 1.2" x 1.2" (30mm x 30mm)

Quantity	Price
1 – 9	$10.83
10 – 99	$10.26
100 +	$9.41

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS27
Quantity Available:		17

Tell a Friend

Related item are:

PCB only of the K27 (CPS27) (Out of Stock)

This is the PCB only of the CPS27 / K27 (TDA7052 Amplifier Module 1W)

Quantity	Price
1 – 9	$2.85
10 – 99	$2.70
100 +	$2.48

Skill Level of Item:		(Component or Part)
Product #		BB268
Quantity Available:		0

You might also consider these items:

audio amplifier 1W (LM386) kit

A kit module designed to be used as a building block in a larger project. The semiconductor LM386 is a general purpose power amplifier designed for use in low voltage applications. Gain may be set between 20 and 200. LM386 data sheet included. Supply voltage: 4 to 12V(CPS17)
PCB size: 1.5in x 1.25in (38mm x 31mm)

Quantity	Price
1 – 9	$10.83
10 – 99	$10.26
100 +	$9.41

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS17
Quantity Available:		4

..........................

2pin connector cable (8 inch)

BB089

Quantity	Price
1 – 9	$0.33
10 – 99	$0.29
100 +	$0.24

Skill Level of Item:		(Component or Part)
Product #		BB089
Quantity Available:		28

..........................

2W amplifier module LM380

This is a very simple amplifier built around the LM380 IC. It can deliver up to 2W into an 8 ohm speaker depending on the supply voltage. Instead of using a heatsink or heat fins the heat produced is dissipated through the center pins of the IC into the copper overlay left on the PCB. If you do require a sustained output of more than ½ watt, you will need to add a heatsink (not included). The IC solders directly to the PCB.
PCB size: 1.75in x 1.75in (45mm x 45mm)

Power output:
> 2 Watt max. (4-8 ohms, 20V)
> 1 Watt max. (4-8 ohms, 12V)
> 0.5 Watt RMS continuous

Quantity	Price
1 – 9	$12.54
10 – 99	$11.88
100 +	$10.89

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS97
Quantity Available:		14

..........................

1W Stereo Amplifier Module

Uses 2 LM386N-1 for a stereo amplifier. Ideal for walkman and other battery powered items. 4V - 12V DC. Instructions PCB and components supplied.

This is a 1 watt per channel, stereo amplifier module Kit using two LM386N IC’s from National Semiconductor. It is basically two of our CPS17’s on a single PC board, with a dual gang pot. It will operate best from 6-12V DC and will work well from a battery since the quiescent current drain is only 10 mA. It requires no heat sinks for normal use. The input and output are both ground referenced. Maximum output will be obtained with a 12V power supply and 8 ohm speaker, however it is particularly suitable for driving headphones from a supply as low as 4V. Speakers are not supplied. They should be rated at 3W or over. PCB size 63mm x 40mm (2.5" x 1.5"). (CPS115)

Quantity	Price
1 – 9	$12.54
10 – 99	$11.88
100 +	$10.89

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS115
Quantity Available:		17

..........................

1W Stereo Amplifier Module DC Volume con

This is a 1 watt stereo amplifier module Kit
using the TDA 7053A from Philips. It uses
a DC voltage to control gain, hence a
single gang pot or switch can be used as a
volume control with minimal tracking error. It
will operate from 4.5 – 18 V DC and requires
no heat-sink for normal use.
TPCB size 1 1/2"x1 3/4" (CPS139)

Quantity	Price
1 – 9	$10.26
10 – 99	$9.72
100 +	$8.91

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS139
Quantity Available:		43

..........................

Stereo Preamplifier - Tone Control Unit

This is a preamplifier and tone control unit
which will make a useful addition to any
of our power amplifier kits. It is extremely
easy to construct due to the use of a special IC,
the Philips TDA 1524A. This contains all the
circuitry required to provide up to 20 dB of
voltage gain, +/-15 dB of bass and treble
control, channel balance, and a switchable
loudness contour.
Specification
D.C. Input : 15V DC supply or 12V DC battery. 50 mA min.
Maximum output : > 3 V RMS
Maximum input : > 300 mV, G = 20 dB
> 3V RMS, G = 0dB. Input Z > 10 k ohm. Output Z < 300 ohm
Frequency resp. : < 10 Hz to > 50 kHz + / – 1 dB
THD at 1kHz : < 0.1 % at 1V output
S/N ratio : > 80 dB, G = 0 dB
Bass boost/cut ~ 15 dB at 50 Hz
Treble boost/cut ~ 15 dB at 15 kHz
PCB size: 4 inches x 2 1/4 inches. (CPS100)

Quantity	Price
1 – 9	$24.23
10 – 99	$22.50
100 +	$21.75

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS100
Quantity Available:		14

..........................

18W BTL Audio Power Amplifier

This kit contains the essential components to build a low voltage, high power mono 18W Bridge Tied Load (BTL) amplifier module using the Hitachi HA13118. The circuit is straight out of the data sheet. Only a few external passive components are required to make the module. The IC contains surge protection circuits and thermal shutdown circuits. The speaker and cables are not included. (CPS105)

Quantity	Price
1 – 9	$17.10
10 – 99	$16.20
100 +	$14.85

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS105
Quantity Available:		11

..........................

Square Wave Oscillator LN/NE555 (inc box

Simple circuit to generate square waves of approximately 1Hz 10Hz 100Hz 1KHz 10KHz & 100KHz. A square wave generator is one of those pieces of equipment that has many uses in the workshop yet few hobbyists actually have. This simple kit, based on the popular 555 timer IC, generates six preset frequencies from 1Hz to 100khz. It has an operating voltage range of 5 to 18VDC and even provides visual indication of the output. The kit is constructed on a single-sided printed circuit board (PCB). The PCB size: is 78 x 50mm (3.1" x 2") and will mount on a small plastic 'Jiffy' box. (CPS111)

Quantity	Price
1 – 9	$14.25
10 – 99	$13.50
100 +	$12.38

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS111
Quantity Available:		29

..........................

Audio to light modulator kit

A music-to-light modulator is a circuit which controls the intensity of one or more lights in response to an audio input. The kit is ideal to give the rhythm to any party or disco without much money. Very safe operation as it uses an opto-coupler as a coupling device between the audio and the mains controlling stages of the circuit.
Input trigger voltage: 2.3 - 2.5V (min)
Operating voltage: 110 or 250 VAC
Power handling: 220W @ 110V or 500W @ 250V
PCB size: 2.16" x 1.63" (To help in the decision to select an enclosure keep in mind that the heat sink used in the kit is about 1" tall.)
PLEASE NOTE, THIS KIT USES 120V MAINS ELECTRICITY AND SHOULD NOT BE ATTEMPTED BY ANYONE WITHOUT THE PROPER SKILL LEVEL. THIS SHOULD ALSO BE BUILT IN A SUITABLE PLASTIC ENCLOSURE.
(CPS12)

Quantity	Price
1 – 9	$14.25
10 – 99	$13.50
100 +	$12.38

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS12
Quantity Available:		31