Rolling Code 10-Channel UHF remote control (kit)

Shopping Cart

	Your Cart is Empty
	View Cart

Documentation in acrobat format (K181)

This kit is based on the cps180 (rolling code 4 channel remote control). It uses the same 4 button remote control, but you will see that 10 keypress combinations are actually supported – the 4 single buttons and 6 two keypress
combinations. This kit takes uses all 10 keypress combinations to operate 10 relays. The 12V relays can switch 120VAC at 1 Amp. Range up to 100'. Up to 15 transmitters can be learnt by one receiver. (includes 1 Transmitter)
(CPS181)

Quantity	Price
1 – 9	$72.19
10 – 99	$67.05
100 +	$64.82

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS181
Quantity Available:		3

Tell a Friend

This item is related to the items below.

UHF 434MHz Automicro 4 button (Transmitter only)

(DA16TX)

Quantity	Price
1 – 9	$22.29
10 – 99	$20.70
100 +	$20.01

Skill Level of Item:		(Assembled and Tested)
Product #		DA16TX
Quantity Available:		6

Rolling Code 2-Channel UHF Remote Control (kit)

This kit is a 2-channel version of CPS180, our 4-channel UHF Remote Control kit. We have simply removed two of the 4 channels from CPS180 and used a 2-button Transmitter unit. Up to 100' range. Up to 15 Transmitter units can be learnt by one Rx unit. (only 1 transmitter included). Although these relays are rated 12A/250VAC the PCB tracks will not carry that current. Please do not put more than 2A through these tracks. If you want to switch higher currect loads then you must jumper some wire between the terminal block pins and the relay pins. Receiver PCB size: L 3.32" x W 2.38" x H 0.88". (CPS157)

Quantity	Price
1 – 9	$52.33
10 – 99	$48.60
100 – 999	$46.98
1000 +	$35.10

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS157
Quantity Available:		5

Rolling Code 4-Channel UHF Remote (partially assembled)

State of the Art, with 4 channels either momentary or latching. Range up to 100'. Up to 15 transmitters can be learned by one receiver. (Includes 1 transmitter) 2 indicator LED's. PCB size: 3 3/8" x 3 1/16" 12VDC 6mA (at rest)(CPA180)

PLEASE NOTE: This is a partially assembled product. The daughter board must still be soldered onto the mother board. 13 solder points. Estimated time to finish: 5 minutes.

Quantity	Price
1 – 9	$70.74
10 – 99	$65.70
100 +	$63.51

Skill Level of Item:		(Partially Assembled)
Product #		CPA180
Quantity Available:		2

Rolling Code 4-Channel UHF Remote control (kit)

State of the Art, with 4 channels either momentary or latching. Range up to 100'. Up to 15 transmitters can be learnt by one receiver. (includes 1 Transmitter) 2 indicator LED's. PCB size: 3 3/8" x 3 1/16" 12VDC 6mA (at rest)(CPS180)

Quantity	Price
1 – 9	$58.14
10 – 99	$54.00
100 +	$52.20

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS180
Quantity Available:		10

You might also consider these items:

Rolling Code 4-Channel UHF Remote (partially assembled)

Quantity	Price
1 – 9	$70.74
10 – 99	$65.70
100 +	$63.51

7407 Hex buffers w open collct out DIP14

(AA552)

Quantity	Price
1 – 9	$0.99
10 – 99	$0.85
100 +	$0.75

Skill Level of Item:		(Component or Part)
Product #		AA552
Quantity Available:		50

40 pin Univ ZIF Socket wide slot

Solder directly to PCB or plug directly into IC socket.
Screw mounting holes for more reliable operation.
(BB007)

Quantity	Price
1 – 9	$12.95
10 – 99	$11.95
100 +	$10.95

Skill Level of Item:		(Component or Part)
Product #		BB007
Quantity Available:		19

DS1820 TO92 IC

The DS1820 Digital Thermometer provides 9–bit temperature readings which indicate the temperature of the device. Information is sent to/from the DS1820 over a 1–Wire interface, so that only one wire (and ground) needs to be connected from a central microprocessor to a DS1820. Power for reading, writing, and performing temperature conversions can be derived from the data line itself with no need for an external power source. Because each DS1820 contains a unique silicon serial number, multiple DS1820s can exist on the same 1–Wire bus. This allows for placing temperature sensors in many different places. Applications
where this feature is useful include HVAC environmental controls, sensing temperatures inside buildings, equipment or machinery, and process monitoring and control.
GND
DQ
VDD
(BB042)

Quantity	Price
1 – 9	$8.99
10 – 99	$8.45
100 +	$7.99

Skill Level of Item:		(Component or Part)
Product #		BB042
Quantity Available:		13

firmware k148 (T2) - Stopwatch with Pause

Another in the series of timer kits based on the K148 hardware platform. This is a classic stopwatch timer with a pause feature as well. Timing is in hours, minutes, seconds and hundredths of a second up to a maximum of ‘99:59:59.99’. An output signal which pulses low every minute is also available. Please note this item requires the CPS148 to work. This is only the firmware chip for CPS148.
(BB073)

Quantity	Price
1 – 9	$10.45
10 – 99	$9.90
100 +	$8.95

Skill Level of Item:		(Component or Part)
Product #		BB073
Quantity Available:		6

Serial Isolated I/O Module (Assembled & Tested)

8-Relay Module (mains rated - 110V and 250VAC.) An extension of our Kit CPS74, PC controlled 8-Relay Board with 250V switching relays and added features. It is in a plastic case, latched relay operation, 250V relays switched in safety by using Dinkle connectors, and with 4 external inputs. Uses serial port so it can be located over 100 yards from the PC. Comes with case and end panel pieces as shown in the photos. Requires a center positive 9-to-12V DC power supply, at least 500mA, 2.5mm jack. (CPA108)

Quantity	Price
1 – 9	$74.95
10 – 99	$69.95
100 +	$65.95

Skill Level of Item:		(Assembled and Tested)
Product #		CPA108
Quantity Available:		15

3 Digit LED Counter (incl box)

Two or more counter modules may be plugged together with the 6-pin sockets and harness provided. Uses a single-unit 3-digit LED display and is built around the 14553 & 14511 chips. Box is provided. The separate COUNTER MODULE shows how to use the kit as a counter. Has COUNT & RESET switches with debounce circuit built in to eliminate problems from noisy switches. May cut off and relocate display. The kit includes data sheets and instructions. 9V battery operation. PCB1 size 1.94"x3.13" (49x78mm). PC2 size 1.31"x 1.38" (33x35mm) (CPS1)

Quantity	Price
1 – 9	$21.32
10 – 99	$19.80
100 +	$19.14

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS1
Quantity Available:		8

Touch/Contact Switch

Both types of switches are built onto the one PCB so you can see and explore how each type works. A battery can power the touch switch (2 contacts) but a power supply (like CPS4) must be used for the touch plate (1 terminal) to work. High quality 12V relay rated at switching 240V/3A supplied. Uses 14011 IC. (CPS10)

Quantity	Price
1 – 9	$9.12
10 – 99	$8.64
100 +	$7.92

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS10
Quantity Available:		5

Stereo Preamplifier - Tone Control Unit

This is a preamplifier and tone control unit
which will make a useful addition to any
of our power amplifier kits. It is extremely
easy to construct due to the use of a special IC,
the Philips TDA 1524A. This contains all the
circuitry required to provide up to 20 dB of
voltage gain, +/-15 dB of bass and treble
control, channel balance, and a switchable
loudness contour.
Specification
D.C. Input : 15V DC supply or 12V DC battery. 50 mA min.
Maximum output : > 3 V RMS
Maximum input : > 300 mV, G = 20 dB
> 3V RMS, G = 0dB. Input Z > 10 k ohm. Output Z < 300 ohm
Frequency resp. : < 10 Hz to > 50 kHz + / – 1 dB
THD at 1kHz : < 0.1 % at 1V output
S/N ratio : > 80 dB, G = 0 dB
Bass boost/cut ~ 15 dB at 50 Hz
Treble boost/cut ~ 15 dB at 15 kHz
PCB size: 4 inches x 2 1/4 inches. (CPS100)

Quantity	Price
1 – 9	$23.26
10 – 99	$21.60
100 +	$20.88

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS100
Quantity Available:		6