Multi Mode Timer (version II) - 8 to 8192sec (2.3h)

Shopping Cart

	Your Cart is Empty
	View Cart

Documentation in acrobat format

Schematic to show how to connect two x CPS152 together to get very long duration timers - to 20 years

A 555 timer IC can be set to 1 second oscillation. The 555 output is fed to a 4020B ripple counter IC. Eleven time outputs from the counter is jumper selectable to an on-board relay. PCB dimensions: 58mm x 53mm.
Power supply: 12VDC (CPS152)

Quantity	Price
1 – 9	$14.25
10 – 99	$13.50
100 +	$12.38

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS152
Quantity Available:		8

Tell a Friend

related items are:

Timer kit 2 - 555 pulse a counter

This is the classic 555 timer circuit switching a relay after a period of time determined by resistor & capacitor connected to the 555. The 555 is used as a monostable. Pot is used to set the time. You can chage the component values & treshold trigger.
Dimensions: 2.375 inches x 1.719 inches
(CPS852)

Quantity	Price
1 – 9	$13.11
10 – 99	$12.42
100 +	$11.39

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS852
Quantity Available:		6

..........................

Timer kit 3 - discharge of capacitor

This is a classic timer circuit using the discharging of an electrolytic capacitor to trigger a transistor switch connected to an on-board relay. Best for up to 400 seconds. All components supplied.(CPS853)

Quantity	Price
1 – 9	$10.83
10 – 99	$10.26
100 +	$9.41

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS853
Quantity Available:		10

..........................

START-STOP TIMER (1s - 60h)

Features
wide timing range
easy time setting
LED animation during operation
on-board START-STOP buttons
non retriggerable
power-on trigger is possible
debounced buffered inputs avoid false triggering
compact size
front panel mountable

Specifications
adjustable delay: 1s - 60h
power supply: 12VDC / 100mA
NO/NC relay: 24VAC/DC 3A max.
dimensions: 70 x 45 x 20mm / 2,8 x 1,8 x 0,8"

(VM141)

Quantity	Price
1 – 9	$27.98
10 – 99	$25.99
100 +	$25.12

Skill Level of Item:		(Assembled and Tested)
Product #		VM141
Quantity Available:		3

..........................

INTERVAL TIMER KIT

For intermittent operation of circuits and equipment. Blinking light, video/photo single frame shooting, slide projector control, miniature models.

Specifications
output relay with dry switch-over contact: 3A/24V
pulse time adjustable: between 0.5 and 5 sec.
pause time adjustable: between 2.5 and 60 sec.
power supply: 12V DC / 100mA
dimensions: 1.6" x 3.4"

Quantity	Price
1 – 9	$5.45
10 – 99	$4.55
100 +	$3.95

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		MK111
Quantity Available:		37

You might also consider these items:

Square Wave Oscillator LN/NE555 (inc box

Simple circuit to generate square waves of approximately 1Hz 10Hz 100Hz 1KHz 10KHz & 100KHz. A square wave generator is one of those pieces of equipment that has many uses in the workshop yet few hobbyists actually have. This simple kit, based on the popular 555 timer IC, generates six preset frequencies from 1Hz to 100khz. It has an operating voltage range of 5 to 18VDC and even provides visual indication of the output. The kit is constructed on a single-sided printed circuit board (PCB). The PCB size: is 78 x 50mm (3.1" x 2") and will mount on a small plastic 'Jiffy' box. (CPS111)

Quantity	Price
1 – 9	$13.68
10 – 99	$12.96
100 +	$11.88

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS111
Quantity Available:		30

..........................

Touch/Contact Switch

Both types of switches are built onto the one PCB so you can see and explore how each type works. A battery can power the touch switch (2 contacts) but a power supply (like CPS4) must be used for the touch plate (1 terminal) to work. High quality 12V relay rated at switching 240V/3A supplied. Uses 14011 IC. (CPS10)

Quantity	Price
1 – 9	$9.12
10 – 99	$8.64
100 +	$7.92

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS10
Quantity Available:		5

..........................

40 pin Univ ZIF Socket wide slot

Solder directly to PCB or plug directly into IC socket.
Screw mounting holes for more reliable operation.
(BB007)

Quantity	Price
1 – 9	$12.95
10 – 99	$11.95
100 +	$10.95

Skill Level of Item:		(Component or Part)
Product #		BB007
Quantity Available:		19

..........................

Rolling Code 4-Channel UHF Remote (partially assembled)

State of the Art, with 4 channels either momentary or latching. Range up to 100'. Up to 15 transmitters can be learned by one receiver. (Includes 1 transmitter) 2 indicator LED's. PCB size: 3 3/8" x 3 1/16" 12VDC 6mA (at rest)(CPA180)

PLEASE NOTE: This is a partially assembled product. The daughter board must still be soldered onto the mother board. 13 solder points. Estimated time to finish: 5 minutes.

Quantity	Price
1 – 9	$70.74
10 – 99	$65.70
100 +	$63.51

Skill Level of Item:		(Partially Assembled)
Product #		CPA180
Quantity Available:		2

..........................

Stereo Preamplifier - Tone Control Unit

This is a preamplifier and tone control unit
which will make a useful addition to any
of our power amplifier kits. It is extremely
easy to construct due to the use of a special IC,
the Philips TDA 1524A. This contains all the
circuitry required to provide up to 20 dB of
voltage gain, +/-15 dB of bass and treble
control, channel balance, and a switchable
loudness contour.
Specification
D.C. Input : 15V DC supply or 12V DC battery. 50 mA min.
Maximum output : > 3 V RMS
Maximum input : > 300 mV, G = 20 dB
> 3V RMS, G = 0dB. Input Z > 10 k ohm. Output Z < 300 ohm
Frequency resp. : < 10 Hz to > 50 kHz + / – 1 dB
THD at 1kHz : < 0.1 % at 1V output
S/N ratio : > 80 dB, G = 0 dB
Bass boost/cut ~ 15 dB at 50 Hz
Treble boost/cut ~ 15 dB at 15 kHz
PCB size: 4 inches x 2 1/4 inches. (CPS100)

Quantity	Price
1 – 9	$23.26
10 – 99	$21.60
100 +	$20.88

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS100
Quantity Available:		6

..........................

Electronic Music Box Engine

This kit is the electronic equivalent of a mechanical music box. Tunes are contained in an IC. Tunes are started by light falling on an LDR. Two music IC's provided. 8ohm 1 watt speaker included. Two IC’s are provided in this kit. M3481 contains 8 Christmas songs. M3485 contains 5 popular tunes: Hawaiian Wedding Song, Try to Remember, Aloha Oe, Love Story & Yesterday. PCB size: 43mm x 34mm (1.69inch x 1.34inch) Power supply: 3VDC (CPS104)

Quantity	Price
1 – 9	$15.39
10 – 99	$14.58
100 +	$13.37

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS104
Quantity Available:		10

..........................

18W BTL Audio Power Amplifier

This kit contains the essential components to build a low voltage, high power mono 18W Bridge Tied Load (BTL) amplifier module using the Hitachi HA13118. The circuit is straight out of the data sheet. Only a few external passive components are required to make the module. The IC contains surge protection circuits and thermal shutdown circuits. The speaker and cables are not included. (CPS105)

Quantity	Price
1 – 9	$16.53
10 – 99	$15.66
100 +	$14.36

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS105
Quantity Available:		11

..........................

Serial Isolated I/O Module (kit)

8-Relay Module (mains rated - 110V and 250VAC.) An extension of our Kit CPS74 (see next kit), PC controlled 8-Relay Board with 250V switching relays and added features. It is in a plastic case, latched relay operation, 250V relays switched in safety by using Dinkle connectors, and with 4 external inputs. Uses serial port so it can be located over 100 yards from the PC. Comes with case and end panel pieces as shown in the photos. Requires a center positive 9-to-12V DC power supply, at least 500mA, 2.5mm jack. (CPS108)

Quantity	Price
1 – 9	$69.95
10 – 99	$64.95
100 +	$59.95

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS108
Quantity Available:		7

..........................

Continuity Tester

Two range tester will buzz up to 3 ohm LO range, and 185 ohm HI range. You can set your own ranges by changing resistor values connected to the LM324 quad op-amp. Full circuit description, PCB and components supplied. A Continuity Tester is one of the most useful pieces of test equipment to have. It is used for testing the electrical path (continuity) between two points. It is more useful and efficient than using a multimeter to do the same job. This Continuity Tester has an audible output so you can keep your eyes on the probe tips while working. In addition it will only 'buzz' through a specified resistance or less. Above this value the tester will not make any sound. A switch is provided to allow this resistance to be varied. The Tester runs from a 9V battery (not supplied). The tester will 'buzz' up to about 2.8 ohm for the LO position and up to 185ohm for the HI position (this may vary slightly due to component tolerances). PCB size: 51mm x 38mm (2" x 1.5"). (CPS110)

Quantity	Price
1 – 99	$10.83
100 +	$9.41

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS110
Quantity Available:		7