18W BTL Audio Power Amplifier

Shopping Cart

	Your Cart is Empty
	View Cart

Documentation in pdf format

Datasheet of the HA13118

(K105)

This kit contains the essential components to build a low voltage, high power mono 18W Bridge Tied Load (BTL) amplifier module using the Hitachi HA13118. The circuit is straight out of the data sheet. Only a few external passive components are required to make the module. The IC contains surge protection circuits and thermal shutdown circuits. The speaker and cables are not included. (CPS105)

Quantity	Price
1 – 9	$20.52
10 – 99	$19.44
100 +	$17.82

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS105
Quantity Available:		17

Tell a Friend

Related items are:

HA13118 18 W BTL Audio Power Amplifier Power IC

The HA13118 is power IC designed for component car stereo amplifiers. At 13.2 V to 4 Ω load, this power IC provides an output power of 18W with 10% distortion.

It is easy to design as this IC employs internal each protection circuit and the new small package.

(BB238)

Quantity	Price
1 – 9	$6.84
10 – 99	$6.48
100 +	$5.94

Skill Level of Item:		(Component or Part)
Product #		BB238
Quantity Available:		1

You might also consider these items:

Stereo Preamplifier - Tone Control Unit

This is a preamplifier and tone control unit
which will make a useful addition to any
of our power amplifier kits. It is extremely
easy to construct due to the use of a special IC,
the Philips TDA 1524A. This contains all the
circuitry required to provide up to 20 dB of
voltage gain, +/-15 dB of bass and treble
control, channel balance, and a switchable
loudness contour.
Specification
D.C. Input : 15V DC supply or 12V DC battery. 50 mA min.
Maximum output : > 3 V RMS
Maximum input : > 300 mV, G = 20 dB
> 3V RMS, G = 0dB. Input Z > 10 k ohm. Output Z < 300 ohm
Frequency resp. : < 10 Hz to > 50 kHz + / – 1 dB
THD at 1kHz : < 0.1 % at 1V output
S/N ratio : > 80 dB, G = 0 dB
Bass boost/cut ~ 15 dB at 50 Hz
Treble boost/cut ~ 15 dB at 15 kHz
PCB size: 4 inches x 2 1/4 inches. (CPS100)

Quantity	Price
1 – 9	$28.10
10 – 99	$26.10
100 +	$25.23

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS100
Quantity Available:		15

..........................

Preamplifier

A preamplifier to use with an electret or other microphone to boost the signal before feeding into an amplifier. Simple and easy to build. PCB Size: 1.75" x 1.25". Power supply: 6 to 12VDC (Electret microphone Included)

Quantity	Price
1 – 9	$13.68
10 – 99	$12.96
100 +	$11.88

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS98
Quantity Available:		36

..........................

6 - 10W Stereo Ampl Mod using TDA2005

Kit 143 is a class AB stereo audio power
amplifier designed for quality hi-fi
applications using a TDA2005 module. It is
easy to construct and has a minimum of
external components. The module has output
current protection and thermal protection. This
is the data book circuit which produces an
excellent sound. The supply voltage required
for this kit is 8 - 18V DC at 1 to 2 Amps.

PCB size 3"x1 3/4"(CPS143)

Quantity	Price
1 – 9	$21.66
10 – 99	$20.52
100 +	$18.81

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS143
Quantity Available:		15

..........................

Voice Recording Module 2 x 20sec sections

The A96020 voice recording module offers true single chip solid state storage capability and requires no software or micro-controller support. It provides high quality recording and playback with dual 20 second message. Sampling rate is 3.2K. Size: 34 x 23 x 11 mm. All you need to do is add a speaker (not included) and 5V DC Power (not included). Features - Non volatile flash memory technology - No battery back up required - User friendly, easy to operate - Slide switch for record or play back - Separate key to trigger message 1 or 2 - Low power consumption - LED to indicate recording and playback - Built-in condenser mic - Automatic power down - 5-6V Operation.

OPTIONAL ITEMS (Not included):
2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
1 x (PB244) Speaker
1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.

(A96020)

Quantity	Price
1 – 9	$8.89
10 – 99	$8.42
100 – 999	$7.72
1000 +	$4.95

Skill Level of Item:		(Assembled and Tested)
Product #		A96020
Quantity Available:		148

..........................

audio amplifier 1W (LM386) kit

A kit module designed to be used as a building block in a larger project. The semiconductor LM386 is a general purpose power amplifier designed for use in low voltage applications. Gain may be set between 20 and 200. LM386 data sheet included. Supply voltage: 4 to 12V(CPS17)
PCB size: 1.5in x 1.25in (38mm x 31mm)

Quantity	Price
1 – 9	$13.68
10 – 99	$12.96
100 +	$11.88

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS17
Quantity Available:		25

..........................

20 second voice recorder/playback module (A93010/A96010)

PLEASE NOTE: This module, part# A96010, could actually be either an A96010 or an A93010 depending on what is in stock at the time. Both are virtually identical and operate the same, but downloadable datasheets are available for each for comparison if necessary. The small size is because the IC is in Chip-on-board form. One button is pushed down to record the message through the on-board electret microphone; A LED turns on during this time. The other button just has to be momentarily pressed to replay the message. A second momentary press during playback will stop the playback. Sampling rate is 4K. All you have to add is the speaker (not included) and 5V DC power (not included). We also have an A96010-kit which in addition to the A96010 also includes a speaker and two cable connectors to connect the unit to a power supply (not included) and the speaker. The record/play time is determined by the 52K resistor. If you change it to 89K you will get 30 seconds but at a reduced sampling rate. Operating current 25mA. Standby current 10 uA. Size: 34 x 23 x 11 mm. The module comes supplied as you see it in the photo.

OPTIONAL ITEMS (Not included):
2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
1 x (PB244) Speaker
1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.

(A96010 & A93010)

Quantity	Price
1 – 9	$6.60
10 – 99	$5.95
100 – 999	$4.95
1000 +	$3.95

Skill Level of Item:		(Assembled and Tested)
Product #		A96010
Quantity Available:		160