Your Cart is Empty
View Cart
 
 
IR Cut-switch Device SH-BSHBIRC
Product Number: SHBIRC
Click image to enlarge
IR cut filters are great for day time images, because the sunlight does not cause a pink hue in the image. However they do not work at night because it blocks out light from an IR light illuminator. The same it true in reverse, without a IR cut filter the night time images turn out very good but the daytime images have a pink discoloration. This cut switch allows the IR filter to be turned on and off. The IR Cut Switch filters out intensive light to create more beautiful and natural image color in either day or night.

Specifications:
  • filter size:ψ8.0mm 
  • rated current:0.090A(3.5-5V)
  • life:100,000 time min
  • DC Resistance:Excite resistance 57± 5Ω(at 20°c) 
  • store temperature range:-20°c To+60°c For72h
  • movable:-10°c To+50°c
  • size:30.5×25.6×5.5mm

Product #: SHBIRC

Skill Level: Assembled and Tested

Additional Details:
AR Glass Specification:
  • Glass shape: 8.4*7.6mm(t=0.40mm)
  • Wave Length(nm): 400~1100nm
  • Transmission(%): T>93%
Blue Glass Specification:
  • Glass shape: 8.4*7.6mm(t=0.55mm)
  • Wave Length(nm): 625±10nm
  • Transmission(%): T=50%
NOTE:
This device functions without a controller board. Here's how it works:


There's basically just a coil in the cut filter that acts as a magnet to move the filter in/out. The IR cut filter coil attaches on the 2-pin micro JST connector - pin 4 is the black wire and pin 5 is the gray wire.

To move the filter out (Night mode) apply the following:
Pin 4 (Black) Ground
Pin 5 (Gray) +5.5V (or greater) pulse 0.5 seconds

To move the filter in (Day mode) apply the following:
Pin 4 (Black) +5.0V pulse 0.5 seconds
Pin 5 (Gray) Ground

The filter will stay in the mode it's switched to after the current is applied. You need to apply a greater voltage than +5V in order to move the filter out, but it takes less current to move the filter back into place. Basically all the controller does is reverse the current to move in/out the filter.


Documentation and Downloads:

Leave a Comment or Ask a Question:

Quantity:  

24  
in stock and available for immediate shipment.

 
Click here for more details
Fused Silica 0.5inch x 0.5inch
Click here for detailed specs.
Description: These cut filters are an insert lens for the cameras; if you remove the 2 screws that attach the lens to the pcb, they can be installed and fit directly into the camera. The filters have a lightpass at about 860nm and are designed to work with IR LEDs emitting at 860nm. This allows the cameras to work during daylight and at night using IR.

Thickness = 0.080inch (~2mm)
Read More
  Component or Part  
  JGS2  
  334  
Quantity:  

IR Cut-switch Device 5V (Device B)
Click here for detailed specs.
Description: IR cut filters are great for day time images, because the sunlight does not cause a pink hue in the image. However they do not work at night because it blocks out light from an IR light illuminator. The same it true in reverse, without a IR cut filter the night time images turn out very good but the daytime images have a pink discoloration. This cut switch allows the IR filter to be turned on and off. The IR Cut Switch filters out intensive light to create more beautiful and natural image color in either day or night.

NOTE: Comes with driver board.

  • Rated Current:  0.556A (AT input 5.0V)
  • Power Current: 2.78w (5.0 DCV Coil)
  • DC Resistance: Excite resistance 9Ω±10% (at 20℃)
  • Operating Voltage: Close → Open : 5.0V;200ms
                                 Open → Close : 5.0V;200ms.
  • Movable Temperature Range: -5℃~+50℃
  • Storage Temperature Range: -20℃~+60℃
  • Dimension: 27.55X27.5X10.6mm
AR Glass: AR Glass Specification:
  • Glass shape:8.4*7.6mm(t=0.40mm)
  • Wave Length(nm):400~1100nm
  • Transmission(%):T>93%
Blue Glass: Blue Glass Specification: 
  • Glass shape:8.4*7.6mm(t=0.55mm)
  • Wave Length(nm):625±10nm
  • Transmission(%):T=50%
Read More
  Assembled and Tested  
  BB271  
  52  
Quantity:  

f6.0mm F1.6 Lens ONLY - as found on C328/C329 camera (BW) (no IR cut filter)
tn_bb224l_general.png
PLEASE NOTE: this is only the lens (NO HOLDER). Lens specs: F/No 1.6 f= 6.0mm FOV = 36 deg diagonal IR cut filter : None (BB224)
Read More
  Component or Part  
  BB224L  
  24  
Quantity:  

Preamplifier kit
Click here for specs, downloads and more pictures.
Description: A preamplifier to use with an electret or other microphone to boost the signal before feeding into an amplifier. Simple and easy to build. PCB Size: 1.75" x 1.25". Power supply: 6 to 12VDC (Electret microphone Included)
Read More
  Kit - Basic Soldering Required  
  CPS98  
  17  
Quantity: