TDA2002 / TDA2003 Amplifier Module kit

Shopping Cart

	Your Cart is Empty
	View Cart

Documentation in acrobat format
(k47)

A proven & popular power amplifier building block for use in any audio project. Power output is dependent on the supply voltage and load resistance. Over 10W is typical for a 16V supply into a 2 ohm speaker. A 12V supply into a 4 ohm speaker will deliver around 4W. Small heatsink provided. In late 2000 the LM383 was discontinued but the TDA2002 is a direct replacement for the LM383. (CPS47)

Quantity	Price
1 – 9	$14.25
10 – 99	$13.50
100 +	$12.38

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS47
Quantity Available:		22

Tell a Friend

You might also consider these items:

18W BTL Audio Power Amplifier (Out of Stock)

This kit contains the essential components to build a low voltage, high power mono 18W Bridge Tied Load (BTL) amplifier module using the Hitachi HA13118. The circuit is straight out of the data sheet. Only a few external passive components are required to make the module. The IC contains surge protection circuits and thermal shutdown circuits. The speaker and cables are not included. (CPS105)

Quantity	Price
1 – 9	$14.25
10 – 99	$13.50
100 +	$12.38

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS105
Quantity Available:		0

Audio to light modulator kit

A music-to-light modulator is a circuit which controls the intensity of one or more lights in response to an audio input. The kit is ideal to give the rhythm to any party or disco without much money. Very safe operation as it uses an opto-coupler as a coupling device between the audio and the mains controlling stages of the circuit.
Input trigger voltage: 2.3 - 2.5V (min)
Operating voltage: 110 or 250 VAC
Power handling: 220W @ 110V or 500W @ 250V
PCB size: 2.16" x 1.63"
PLEASE NOTE, THIS KIT USES 120V MAINS ELECTRICITY AND SHOULD NOT BE ATTEMPTED BY ANYONE WITHOUT THE PROPER SKILL LEVEL. THIS SHOULD ALSO BE BUILT IN A SUITABLE PLASTIC ENCLOSURE.
(CPS12)

Quantity	Price
1 – 9	$11.97
10 – 99	$11.34
100 +	$10.40

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS12
Quantity Available:		59

Stereo Preamplifier - Tone Control Unit

This is a preamplifier and tone control unit
which will make a useful addition to any
of our power amplifier kits. It is extremely
easy to construct due to the use of a special IC,
the Philips TDA 1524A. This contains all the
circuitry required to provide up to 20 dB of
voltage gain, +/-15 dB of bass and treble
control, channel balance, and a switchable
loudness contour.
Specification
D.C. Input : 15V DC supply or 12V DC battery. 50 mA min.
Maximum output : > 3 V RMS
Maximum input : > 300 mV, G = 20 dB
> 3V RMS, G = 0dB. Input Z > 10 k ohm. Output Z < 300 ohm
Frequency resp. : < 10 Hz to > 50 kHz + / – 1 dB
THD at 1kHz : < 0.1 % at 1V output
S/N ratio : > 80 dB, G = 0 dB
Bass boost/cut ~ 15 dB at 50 Hz
Treble boost/cut ~ 15 dB at 15 kHz
PCB size: 4 inches x 2 1/4 inches. (CPS100)

Quantity	Price
1 – 9	$20.35
10 – 99	$18.90
100 +	$18.27

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS100
Quantity Available:		10

Electronic Music Box Engine

This kit is the electronic equivalent of a mechanical music box. Tunes are contained in an IC. Tunes are started by light falling on an LDR. Two music IC's provided. 8ohm 1 watt speaker included. PCB size: 43mm x 34mm (1.69inch x 1.34inch)
Power supply: 3VDC (CPS104)

Quantity	Price
1 – 9	$14.82
10 – 99	$14.04
100 +	$12.87

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS104
Quantity Available:		9

Square Wave Oscillator LN/NE555 (inc box

Simple circuit to generate square waves of approximately 1Hz 10Hz 100Hz 1KHz 10KHz & 100KHz. A square wave generator is one of those pieces of equipment that has many uses in the workshop yet few hobbyists actually have. This simple kit, based on the popular 555 timer IC, generates six preset frequencies from 1Hz to 100khz. It has an operating voltage range of 5 to 18VDC and even provides visual indication of the output. The kit is constructed on a single-sided printed circuit board (PCB). The PCB size: is 78 x 50mm (3.1" x 2") and will mount on a small plastic 'Jiffy' box. (CPS111)

Quantity	Price
1 – 9	$13.68
10 – 99	$12.96
100 +	$11.88

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS111
Quantity Available:		32

1W Stereo Amplifier Module

Uses 2 LM386N-1 for a stereo amplifier. Ideal for walkman and other battery powered items. 4V - 12V DC. Instructions PCB and components supplied.

This is a 1 watt per channel, stereo amplifier module Kit using two LM386N IC’s from National Semiconductor. It is basically two of our CPS17’s on a single PC board, with a dual gang pot. It will operate best from 6-12V DC and will work well from a battery since the quiescent current drain is only 10 mA. It requires no heat sinks for normal use. The input and output are both ground referenced. Maximum output will be obtained with a 12V power supply and 8 ohm speaker, however it is particularly suitable for driving headphones from a supply as low as 4V. Speakers are not supplied. They should be rated at 3W or over. PCB size 63mm x 40mm (2.5" x 1.5"). (CPS115)

Quantity	Price
1 – 9	$10.83
10 – 99	$10.26
100 +	$9.41

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS115
Quantity Available:		23

Positive Adjustable Power Supply Module

Compact positive adjustable power supply +/- 1.5V to 35V depending on input power source. On-board heatsink. It is ideal for powering any application requiring a DC supply at current levels up to 1.5A
FEATURES:
· Output reverse polarity and back-voltage protection
· LED power on indication
· On board heatsink for IC regulator
· Variable output voltage
· AC or DC input voltage
· Low noise (uses linear regulator)
· Screw terminals for input, output and LED indicator
· PCB size: (84 x 37 mm) (3.1" x 1.5")
This kit can be combined with Kit CPS125 to create a dual-rail supply. The kit is constructed on a single-sided printed circuit board (PCB).
(CPS124)

Quantity	Price
1 – 9	$14.25
10 – 99	$13.50
100 +	$12.38

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS124
Quantity Available:		9

Mini-Vox and Relay kit

The idea behind a VOX (voice activated switch) is that instead of the user pressing a switch to activate a relay, the sound of the users voice itself activates the relay. This gives hands-free control over devices like tape recorders. Power supply needed: 12VDC center positive 2.5mm jack. Electret microphone to pick up the sound is included. PCB size: 44mm x 48mm (1.73inch x 1.89inch).
(CPS126)

Quantity	Price
1 – 9	$11.97
10 – 99	$11.34
100 +	$10.40

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS126
Quantity Available:		16

VOX for automatic recording 6v kit

This is a very sensitive, sound or voice activated switch which plugs into the REMOTE plug of a tape recorder and turns it on when it detects a preselected level of sound. If the sound continues then the switch will self trigger and remain on. Once the sound goes away then a delay in the circuit will turn off the tape recorder after about 6 seconds. It is ideal for hands free operation of a tape recorder. It has a MIC input, a delay circuit and adjustable sensitivity. Battery holder for 4xAA batteries included.
Operating voltage: 6 Volt (CPS13)

Quantity	Price
1 – 9	$11.40
10 – 99	$10.80
100 +	$9.90

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS13
Quantity Available:		3