Speaker Round 3 inch 8 ohm 1 watt

Shopping Cart

	Your Cart is Empty
	View Cart

Diameter: 76mm (3 inch)
1 Watt
8 Ohm

Quantity	Price
1 – 9	$3.99
10 – 99	$3.78
100 – 999	$3.47
1000 +	$3.19

Skill Level of Item:		(Component or Part)
Product #		PB244
Quantity Available:		112

Tell a Friend

Related items are:

40mm (1.6in) metal housing mylar speaker 0.25W

40mm (1.6in) metal housing mylar speaker 0.25W
Specifications:
- 0.25W
- 40mm (1.57in)
- 16 Ohm
- RoHS Compliant
- Includes 5 inch wires already soldered to contacts of the speaker.

Quantity	Price
1 – 9	$0.61
10 – 99	$0.51
100 – 999	$0.46
1000 +	$0.39

Skill Level of Item:		(Component or Part)
Product #		PB240
Quantity Available:		931

20 second voice recorder/playback module (A93010/A96010)

PLEASE NOTE: This module, part# A96010, could actually be either an A96010 or an A93010 depending on what is in stock at the time. Both are virtually identical and operate the same, but downloadable datasheets are available for each for comparison if necessary. The small size is because the IC is in Chip-on-board form. One button is pushed down to record the message through the on-board electret microphone; A LED turns on during this time. The other button just has to be momentarily pressed to replay the message. A second momentary press during playback will stop the playback. Sampling rate is 4K. All you have to add is the speaker (not included) and 5V DC power (not included). We also have an A96010-kit which in addition to the A96010 also includes a speaker and two cable connectors to connect the unit to a power supply (not included) and the speaker. The record/play time is determined by the 52K resistor. If you change it to 89K you will get 30 seconds but at a reduced sampling rate. Operating current 25mA. Standby current 10 uA. Size: 34 x 23 x 11 mm. The module comes supplied as you see it in the photo.

OPTIONAL ITEMS (Not included):
2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
1 x (PB244) Speaker
1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.

(A96010 & A93010)

Quantity	Price
1 – 9	$6.60
10 – 99	$5.95
100 – 999	$4.95
1000 +	$3.95

Skill Level of Item:		(Assembled and Tested)
Product #		A96010
Quantity Available:		99

Voice Recording Module 2 x 20sec sections

The A96020 voice recording module offers true single chip solid state storage capability and requires no software or micro-controller support. It provides high quality recording and playback with dual 20 second message. Sampling rate is 3.2K. Size: 34 x 23 x 11 mm. All you need to do is add a speaker (not included) and 5V DC Power (not included). Features - Non volatile flash memory technology - No battery back up required - User friendly, easy to operate - Slide switch for record or play back - Separate key to trigger message 1 or 2 - Low power consumption - LED to indicate recording and playback - Built-in condenser mic - Automatic power down - 5-6V Operation.

OPTIONAL ITEMS (Not included):
2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
1 x (PB244) Speaker
1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.

(A96020)

Quantity	Price
1 – 9	$8.89
10 – 99	$8.42
100 – 999	$7.72
1000 +	$4.95

Skill Level of Item:		(Assembled and Tested)
Product #		A96020
Quantity Available:		64

You might also consider these items:

2pin connector cable (8 inch)

Quantity	Price
1 – 9	$0.33
10 – 99	$0.29
100 +	$0.24

Skill Level of Item:		(Component or Part)
Product #		BB089
Quantity Available:		238

TDA7052 Amplifier Module 1W

A 1W power amplifier building block designed to be part of a larger project. Ideal as a low power battery operated amplifier (from 3 to 15V) driving an 8 ohm speaker. The Philips TDA7052 is a general purpose amplifier. No heatsink needed. Short circuit protected. PCB size: 1.2" x 1.2" (30mm x 30mm)

Quantity	Price
1 – 9	$13.68
10 – 99	$12.96
100 +	$11.88

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS27
Quantity Available:		30

audio amplifier 1W (LM386) kit

A kit module designed to be used as a building block in a larger project. The semiconductor LM386 is a general purpose power amplifier designed for use in low voltage applications. Gain may be set between 20 and 200. LM386 data sheet included. Supply voltage: 4 to 12V(CPS17)
PCB size: 1.5in x 1.25in (38mm x 31mm)

Quantity	Price
1 – 9	$13.68
10 – 99	$12.96
100 +	$11.88

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS17
Quantity Available:		9

Click here for specs, downloads, and more pictures.

KC7783 PIR Detector Module (Assem and tested)

This is a fully assembled and tested miniature PIR module (KC7783 with KC778B IC) with only 3 connections: Power, Ground & Output. Rated for 4 - 12VDC input power. Uses RE200B PIR sensor. Output is an active high pulse of approx. 0.5 seconds and remains active as long as there is motion. Range up to 10 feet. PCB size: 35mm x 25mm(CPS76)

Quantity	Price
1 – 9	$9.45
10 – 99	$7.95
100 – 999	$6.95
1000 +	$5.45

Skill Level of Item:		(Component or Part)
Product #		CPS76
Quantity Available:		458

2W amplifier module LM380

This is a very simple amplifier built around the LM380 IC. It can deliver up to 2W into an 8 ohm speaker depending on the supply voltage. Instead of using a heatsink or heat fins the heat produced is dissipated through the center pins of the IC into the copper overlay left on the PCB. If you do require a sustained output of more than ½ watt, you will need to add a heatsink (not included). The IC solders directly to the PCB.
PCB size: 1.75in x 1.75in (45mm x 45mm)

Power output:
> 2 Watt max. (4-8 ohms, 20V)
> 1 Watt max. (4-8 ohms, 12V)
> 0.5 Watt RMS continuous

Quantity	Price
1 – 9	$14.25
10 – 99	$13.50
100 +	$12.38

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS97
Quantity Available:		10

MK484/TA7642 am-radio IC (TO92) (Out of Stock)

MK484/TA7642 am-radio IC (TO92)

Quantity	Price
1 – 9	$2.14
10 – 99	$1.80
100 +	$1.62

Skill Level of Item:		(Component or Part)
Product #		BB044
Quantity Available:		0

KC7783R PIR Detector Module (Low cost version) (Assem and tested)

Mechanical and electrical specs is the same as the KC7783 except for a lower cost IC (KC778B IC) package used in this KC7783R RoHS compliant: YES. (BB054)

Quantity	Price
1 – 9	$8.98
10 – 99	$7.45
100 – 999	$6.75
1000 – 9999	$5.75
10000 +	$4.95

Skill Level of Item:		(Component or Part)
Product #		BB054
Quantity Available:		412

Preamplifier

A preamplifier to use with an electret or other microphone to boost the signal before feeding into an amplifier. Simple and easy to build. PCB Size: 1.75" x 1.25". Power supply: 6 to 12VDC (Electret microphone Included)

Quantity	Price
1 – 9	$13.68
10 – 99	$12.96
100 +	$11.88

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS98
Quantity Available:		21

Melody Card Happy Birthday COB Module

Complete Card Melody Unit- 'Happy Birthday' Melody IC COB, battery and piezo all ready to play. As found in Christmas cards and books which play when you open the page. Self-adhesive backing. Tune repeats continuously while power is connected. Total of 128 notes. Cmos LSI.

Quantity	Price
1 – 9	$0.99
10 – 99	$0.85
100 – 999	$0.75
1000 – 9999	$0.65
10000 +	$0.55

Skill Level of Item:		(Assembled and Tested)
Product #		SG13
Quantity Available:		13