2pin connector cable (8 inch)

Shopping Cart

	Your Cart is Empty
	View Cart

BB089

Quantity	Price
1 – 9	$0.33
10 – 99	$0.29
100 +	$0.24

Skill Level of Item:		(Component or Part)
Product #		BB089
Quantity Available:		128

Tell a Friend

Related items are:

20 second voice recorder/playback module (A93010/A96010)

PLEASE NOTE: A96010 or A93010 is supplied depending on availability. Currently only A93010 is available and is the one that is been sold. A96010 is not currently available. The small size is because the IC is in Chip-on-board form. One button is pushed down to record the message. The electret microphone is on the board. The LED turns on during this time. The other button just has to be momentarily pressed to replay the message. A second momentary press during playback will stop the playback. Sampling rate is 4K. All you have to add is the speaker (not included) and 5V DC power (not included). The record play time is determined by the 52K resistor. If you change it to 89K you will get 30 seconds but at a reduced sampling rate. Operating current 25mA. Standby current 10 uA. Size: 34 x 23 x 11 mm. The module comes supplied as you see it in the photo.

OPTIONAL ITEMS (Not included):
2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
1 x (PB244) Speaker
1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.

(A96010 & A93010)

Quantity	Price
1 – 9	$6.60
10 – 99	$5.95
100 – 999	$4.95
1000 +	$3.95

Skill Level of Item:		(Assembled and Tested)
Product #		A96010
Quantity Available:		128

Voice Recording Module 2 x 20sec sections

The A96020 voice recording module offers true single chip solid state storage capability and requires no software or micro-controller support. It provides high quality recording and playback with dual 20 second message. Sampling rate is 3.2K. Size: 34 x 23 x 11 mm. All you need to do is add a speaker (not included) and 5V DC Power (not included). Features - Non volatile flash memory technology - No battery back up required - User friendly, easy to operate - Slide switch for record or play back - Separate key to trigger message 1 or 2 - Low power consumption - LED to indicate recording and playback - Built-in condenser mic - Automatic power down - 5-6V Operation.

OPTIONAL ITEMS (Not included):
2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
1 x (PB244) Speaker
1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.

(A96020)

Quantity	Price
1 – 9	$8.89
10 – 99	$8.42
100 – 999	$7.72
1000 +	$4.95

Skill Level of Item:		(Assembled and Tested)
Product #		A96020
Quantity Available:		73

You might also consider these items:

Voice Recording Module 2 x 20sec sections

Quantity	Price
1 – 9	$8.89
10 – 99	$8.42
100 – 999	$7.72
1000 +	$4.95

20 second voice recorder/playback module (A93010/A96010)

Quantity	Price
1 – 9	$6.60
10 – 99	$5.95
100 – 999	$4.95
1000 +	$3.95

Speaker Round 3 inch 8 ohm 1 watt

Diameter: 76mm (3 inch)
1 Watt
8 Ohm

Quantity	Price
1 – 9	$3.65
10 – 99	$3.46
100 +	$3.17

Skill Level of Item:		(Component or Part)
Product #		PB244
Quantity Available:		75

Battery clip for 9V PP3 Battery

Specifications
I-type
low-cost
(SNAP9V)

Quantity	Price
1 – 9	$0.21
10 – 99	$0.18
100 +	$0.16

Skill Level of Item:		(Component or Part)
Product #		SNAP9V
Quantity Available:		72

TDA7052 Amplifier Module 1W (Out of Stock)

A 1W power amplifier building block designed to be part of a larger project. Ideal as a low power battery operated amplifier (from 3 to 15V) driving an 8 ohm speaker. The Philips TDA7052 is a general purpose amplifier. No heatsink needed. Short circuit protected. PCB size: 1.2" x 1.2" (30mm x 30mm)

Quantity	Price
1 – 9	$11.40
10 – 99	$10.80
100 +	$9.90

Skill Level of Item:		(Kit - Basic Soldering Required)
Product #		CPS27
Quantity Available:		0

KC7783 PIR Detector Module (Assem and tested)

This is a fully assembled and tested miniature PIR module (KC7783 with KC778B IC) with only 3 connections: Power, Ground & Output. Rated for 4 - 12VDC input power. Uses RE200B PIR sensor. Output is an active high pulse of approx. 0.5 seconds and remains active as long as there is motion. Range up to 10 feet. PCB size: 35mm x 25mm(CPS76)

Quantity	Price
1 – 9	$9.45
10 – 99	$7.95
100 – 999	$6.95
1000 +	$5.45

Skill Level of Item:		(Component or Part)
Product #		CPS76
Quantity Available:		972

Battery holder 4 x AA cells 57x30x27mm

MB059

Quantity	Price
1 – 9	$1.19
10 – 99	$1.00
100 +	$0.90

Skill Level of Item:		(Component or Part)
Product #		MB059
Quantity Available:		15

Toy motor kit

Construct a working DC Motor. This clever kit has been delighting children for decades. All parts provided, including: 2 coils of copper wire; base; field pole; armature core; brushes; all fasteners. Instruction booklet with theory and experiments included.
Operates on 3 to 6 volt batteries (not included). (CPN135S)

Quantity	Price
1 – 9	$5.45
10 – 99	$5.25
100 +	$4.95

Skill Level of Item:		(Kit - No Soldering Required)
Product #		CPN135S
Quantity Available:		42

KC7786 PIR sensor module 12v (3pin .1in)

This is a fully assembled and tested miniature PIR module (KC7786 with KC778B COB IC) with only 3 connections: Power, Ground & Output (3 pin terminal of standard 0.1 inch pitch). Rated for 12VDC input power. Uses RE200B PIR sensor. Output is an active high pulse of approx. 0.5 seconds and remains active as long as there is motion. Range up to 10 feet. PCB size: 27mm x 27mm (BB043)

Quantity	Price
1 – 9	$11.35
10 – 99	$9.95
100 – 999	$8.95
1000 – 9999	$8.15
10000 +	$7.45

Skill Level of Item:		(Component or Part)
Product #		BB043
Quantity Available:		143