Kits and Modules > Radio > 
Your Cart is Empty
View Cart
 
 
Radio
Rolling Code 2-Channel UHF Remote Control (kit)
tn_cps157a.jpg
Description: This kit is a 2-channel version of CPS180, our 4-channel UHF Remote Control kit. We have simply removed two of the 4 channels from CPS180 and used a 2-button Transmitter unit. Up to 100' range. Up to 15 Transmitter units can be learned by one Rx unit. (only 1 transmitter included). Although these relays are rated 12A/250VAC the PCB tracks will not carry that current. Please do not put more than 2A through these tracks. If you want to switch higher currect loads then you must jumper some wire between the terminal block pins and the relay pins. Receiver PCB size: L 3.32" x W 2.38" x H 0.88". (CPS157)
Read More
  Kit - Basic Soldering Required  
  CPS157  
  8  
Quantity:  

Rolling Code 4-Channel UHF Remote control (V3) (kit)
Click here for detailed specs.
State of the Art, with 4 channels either momentary or latching. 
Now also with reset
Range up to 100'. 
Up to 15 transmitters can be learned by one receiver. 
(includes 1 Transmitter) 
2 indicator LED's. 
PCB size: 3 1/2" x 2 7/8" (89 mm x 73 mm)
12VDC 6mA (at rest)
Read More
  Kit - Basic Soldering Required  
  CPS180  
  1  
Quantity:  

UHF 434MHz Automicro 4 Button (Transmitter only)
tn_da16tx.jpg
UHF 434MHz Automicro 4 button (Transmitter only)
Read More
  Assembled and Tested  
  DA16TX  
  3  
Quantity:  

UHF 434MHz Automicro Receiver only
tn_da16rx.jpg
Processes the received signal via a bandpass filter, amplifier and Schmitt trigger. Its output delivers a digital pulse train to the decoder IC. Please note that the receiver module must be built into a circuit by the user. It does nothing as supplied here. PCB size: 47mm x 16mm (1.85inch x 0.63inch)(DA16RX)
Read More
  Assembled and Tested  
  DA16RX  
  6  
Quantity:  

Rolling Code 10-Channel UHF remote control (kit)
tn_cps181.jpg
This kit is based on the cps180 (rolling code 4 channel remote control). It uses the same 4 button remote control, but you will see that 10 keypress combinations are actually supported – the 4 single buttons and 6 two keypress
combinations. This kit takes uses all 10 keypress combinations to operate 10 relays. The 12V relays can switch 120VAC at 1 Amp. Range up to 100'. Up to 15 transmitters can be learned by one receiver. (includes 1 Transmitter)
(CPS181)
Read More
  Kit - Basic Soldering Required  
  CPS181  
  1  
Quantity:  

One Chip AM Radio
tn_cps63.jpg
Complete AM radio on a PCB. Tuned radio frequency front-end, single chip RF amplifier & detector and two stages of amplification of the audio signal into a speaker. All components supplied. Coil prewound. Excellent for schools.(CPS63)
Read More
  Kit - Basic Soldering Required  
  CPS63  
  2  
Quantity:  

Antenna amplifier kit (30 to 850 mhz)
tn_cps7008f.jpg
This is an antenna amplifier kit that covers a wide frequency range. Use it for
amplifying low power VHF / UHF television signals and for the amateur radio
bands. Adjustments are not required. A metal enclosure is required for the
amplifier. Coaxial cable is required for the input signal (from the antenna) and
the output signal (output of the amplifier). Specifications: • Supply Voltage: 9
- 12Vdc (regulated) • Frequency Range: 30 - 850MHz • Gain: 20dB • Input / Output
Impedance: 60 Ohm • Dimensions: 56 x 56mm, 15mm height Not Included: • 50 Ohm
Coaxial Cable:
Read More
  Kit - Basic Soldering Required  
  MB095  
  2  
Quantity:  

car interference suppressor kit
tn_cps1097.jpg
A simple circuit that was designed to eliminate the interference signals generated by a car’s engine. These signals are particularly annoying when trying to listen to weak radio broadcasts. The car renders very useful services to its owner. Unfortunately, it also produces a high level of radio frequency interference signals originating from the car’s generator, wipers, flash indicators and air conditioning. (CPS1097)
Read More
  Assembled and Tested  
  CPS1097  
  1  
Quantity:  

FM RADIO
tn_mk118.jpg
Features:

double fun: building and listening!
easy to assemble: no coils to wind
one single adjustment
pre-assembled and tested FM front end
receives the complete FM band: 88-108 MHz
with ON/OFF switch, volume control and LED indicator 

Specifications:

power supply: 12V DC / 100mA (adaptor jack provided)
dimensions: 4.8" x 3.3" 
(MK118)
Read More
  Kit - Basic Soldering Required  
  MK118  
  2  
Quantity:  

1-CHANNEL IR CODE LOCK TRANSMITTER
Click here for specs, downloads, and more pictures.
A choice can be made from over 8000 codes.

Specifications:

one channel
distance transmitter / receiver: ± 23'
LED on / off indication and battery level indication
key holder housing
power supply: 12V battery type V23GA, GP23GAC (not incl.)
dimensions: 1.4" x 0.6" x 2.2"
 
(K6708)
Read More
  Kit - Basic Soldering Required  
  K6708  
  3  
Quantity:  

IR REMOTE CONTROLLED DIMMER
Click here for specs, downloads, and more pictures.
This one channel IR receiver/dimmer works together with the 15 channel IR transmitter (K6710 & K8049). The receiver code can be set to 1 of the 15 transmitter codes so that 15 receivers can be operated (K6712 and/or K6713) independently of each other. Thanks to its compact design this kit fits into a standard light switch housing.

Specifications:

max. load: 2A (4A with heatsink)
supply voltage: 110V AC / 60Hz
transmitter / receiver distance: max. 23'
not suitable for halogen lights 
(K6712)
Read More
  Kit - Basic Soldering Required  
  K6712  
  3  
Quantity:  

8-CHANNEL RF REMOTE TRANSMITTER
tn_vm118_remote.jpg
Features:

8 addresses allow the use of multiple receivers
'all clear'- function
open-field range up to 50m
toggle or momentary mode for each key

Specifications:

power supply: 3 AAA batteries
433MHz operation
8 digitalkodade kanaler
rubber keypad
LED function/mode indication
FCC approved ID code: NLO8058
(VM118R)
Read More
  Assembled and Tested  
  VM118R  
  2  
Quantity: