Your Cart is Empty
View Cart
 
 
Audio Amplifier 1W (LM386) KitCPS17
Product Number: CPS17
Click image to enlarge
Description: A kit module designed to be used as a building block in a larger project. The semiconductor LM386 is a general purpose power amplifier designed for use in low voltage applications. Gain may be set between 20 and 200. LM386 data sheet included. Supply voltage: 4 to 12V.

PCB size: 1.5in x 1.25in (38mm x 31mm)

Product #: CPS17

Skill Level: Kit - Basic Soldering Required

Additional Details:

Documentation and Downloads:

Leave a Comment or Ask a Question:

Quantity:  

50  
in stock and available for immediate shipment.

 
Click here for more details
Audio Amplifier 1W (LM386) (Assembled)
Click here for specs, downloads and more pictures.
Description: A kit module designed to be used as a building block in a larger project. The semiconductor LM386 is a general purpose power amplifier designed for use in low voltage applications. Gain may be set between 20 and 200. LM386 data sheet included. Supply voltage: 4 to 12V.

PCB size: 1.5in x 1.25in (38mm x 31mm)

NOTE: Please allow 24 hours for assembly!
Read More
  Assembled and Tested  
  CPS17-TBA  
  50  
Quantity:  

   
TDA7052 Amplifier Module 1W (kit)
tn_cps27.jpg
Description: A 1W power amplifier building block designed to be part of a larger project. Ideal as a low power battery operated amplifier (from 3 to 15V) driving an 8 ohm speaker. The Philips TDA7052 is a general purpose amplifier. No heatsink needed. Short circuit protected. PCB size: 1.2" x 1.2" (30mm x 30mm)
Read More
  Kit - Basic Soldering Required  
  CPS27  
  65  
Quantity:  

Preamplifier kit
Click here for specs, downloads and more pictures.
Description: A preamplifier to use with an electret or other microphone to boost the signal before feeding into an amplifier. Simple and easy to build. PCB Size: 1.75" x 1.25". Power supply: 6 to 12VDC (Electret microphone Included)
Read More
  Kit - Basic Soldering Required  
  CPS98  
  17  
Quantity:  

Audio to Light Modulator Kit
tn_cps12_kit.png
Description: A music-to-light modulator is a circuit which controls the intensity of one or more lights in response to an audio input. The kit is ideal to give the lights rhythm to any party or disco without much money. Very safe operation as it uses an opto-coupler as a coupling device between the audio and the mains controlling stages of the circuit.

Specifications:
  • Input trigger voltage: 2.3 - 2.5V (min)
  • Operating voltage: 110 or 250 VAC
  • Power handling: 220W @ 110V or 500W @ 250V
  • PCB size: 2.16" x 1.63" (To help in the decision to select an enclosure keep in mind that the heat sink used in the kit is about 1" tall.)

PLEASE NOTE: THIS KIT USES 120V MAINS ELECTRICITY AND SHOULD NOT BE ATTEMPTED BY ANYONE WITHOUT THE PROPER SKILL LEVEL. THIS SHOULD ALSO BE BUILT IN A SUITABLE PLASTIC ENCLOSURE.
Read More
  Kit - Basic Soldering Required  
  CPS12  
  41  
Quantity:  

Speaker Round 3 inch 8 ohm 1 watt
tn_pb244_general.png
Specifications:
  • Diameter: 76mm (3 inch)
  • 1 Watt
  • 8 Ohm
Read More
  Component or Part  
  PB244  
  101  
Quantity:  

20 Second Voice Recorder/Playback Module (A93010)
tn_a96010_general.png
PLEASE NOTE: This module, part# A96010, is actually an A93010. It is virtually identical to the A96010 and it operates the same, but downloadable datasheets are available for each for comparison if necessary. The small size is because the IC is in Chip-on-board form. One button is pushed down to record the message through the on-board electret microphone; A LED turns on during this time. The other button just has to be momentarily pressed to replay the message. A second momentary press during playback will stop the playback. Sampling rate is 4K. All you have to add is the speaker (not included) and 5V DC power (not included). We also have an A96010-kit which in addition to the part# A96010 also includes a speaker and two cable connectors to connect the unit to a power supply (not included) and the speaker. The record/play time is determined by the 52K resistor. If you change it to 89K you will get 30 seconds but at a reduced sampling rate. Operating current 25mA. Standby current 10 uA. Size: 34 x 23 x 11 mm. The module comes supplied as you see it in the photo. 

OPTIONAL ITEMS (Not included):
  • 2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
  • 1 x (PB244) Speaker
  • 1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.
Read More
  Assembled and Tested  
  A96010  
  46  
Quantity:  

TDA2002 / TDA2003 Amplifier Module Kit
Click here for detailed specs.
Description: A proven & popular power amplifier building block for use in any audio project. Power output is dependent on the supply voltage and load resistance. Over 10W is typical for a 16V supply into a 2 ohm speaker. A 12V supply into a 4 ohm speaker will deliver around 4W. Small heatsink provided. In late 2000 the LM383 was discontinued but the TDA2002 is a direct replacement for the LM383.
Read More
  Kit - Basic Soldering Required  
  CPS47  
  14  
Quantity: