Your Cart is Empty
View Cart
 
 
20 Second Voice Recorder/Playback Module (A93010)A96010
Product Number: A96010
Click image to enlarge
PLEASE NOTE: This module, part# A96010, is actually an A93010. It is virtually identical to the A96010 and it operates the same, but downloadable datasheets are available for each for comparison if necessary. The small size is because the IC is in Chip-on-board form. One button is pushed down to record the message through the on-board electret microphone; A LED turns on during this time. The other button just has to be momentarily pressed to replay the message. A second momentary press during playback will stop the playback. Sampling rate is 4K. All you have to add is the speaker (not included) and 5V DC power (not included). We also have an A96010-kit which in addition to the part# A96010 also includes a speaker and two cable connectors to connect the unit to a power supply (not included) and the speaker. The record/play time is determined by the 52K resistor. If you change it to 89K you will get 30 seconds but at a reduced sampling rate. Operating current 25mA. Standby current 10 uA. Size: 34 x 23 x 11 mm. The module comes supplied as you see it in the photo. 

OPTIONAL ITEMS (Not included):
  • 2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
  • 1 x (PB244) Speaker
  • 1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.

Product #: A96010

Skill Level: Assembled and Tested

Additional Details:
NOTE: This unit will power a 1 watt speaker as is. You do not need to add an external amplifier. However, you can add an external amplifier if you want - as long as you follow the instructions below.

Use this schematic to add a potentiometer when using an additional external amplifier:



When using an external amplifier, you'll need a potentiometer (recommended part# HB165) to decrease the high output signal from the A96010 enough to get a clear sound.


Documentation and Downloads:

Leave a Comment or Ask a Question:

Quantity:  

38  
in stock and available for immediate shipment.

 
Click here for more details
2pin connector cable (8 inch)
tn_bb089.jpg
2pin connector cable (8 inch)
Read More
  Component or Part  
  BB089  
  83  
Quantity:  

40mm (1.6in) Metal Housing Mylar Speaker 0.25W
Click here for specs, downloads and more pictures.
Specifications:
  • 0.25W
  • 40mm (1.57in)
  • 16 Ohm
Read More
  Component or Part  
  PB240  
  216  
Quantity:  

Speaker Round 3 inch 8 ohm 1 watt
tn_pb244_general.png
Specifications:
  • Diameter: 76mm (3 inch)
  • 1 Watt
  • 8 Ohm
Read More
  Component or Part  
  PB244  
  114  
Quantity:  

2" Paper Cone Midrange Tweeter 4 Ohm
Click here for specs, downloads, and more pictures!
Features:
  • The SAS Bazooka 5" shielded midbass driver features a stamped steel frame, inverted concave diaphragm, foam half roll surround, and flat spider.
  • It boasts high power handling and smooth response, thanks to an optimized ceramic ferrite magnet and copper 4-layer voice coil on an aluminum former.
  • The WF5R-MM's 2 ohm rating makes it great for mobile sound applications; also for home use when used in multiples to achieve higher system impedances.
  • Made in Brazil by Bravox. Buyout, limited quantities.
  • Read More...

Read More
  Component or Part  
  PB300  
  18  
Quantity:  

A96010 Kit (A96010 with Wires and Speaker Included)
tn_a96010-kit_general.png
PLEASE NOTE: This module, part # A96010, is actually an A93010. It is virtually identical to the A96010 and it operates the same, but downloadable datasheets are available for each for comparison if necessary. The small size is because the IC is in Chip-on-board form. One button is pushed down to record the message through the on-board electret microphone; A LED turns on during this time. The other button just has to be momentarily pressed to replay the message. A second momentary press during playback will stop the playback. Sampling rate is 4K. All you have to add is the speaker (not included) and 5V DC power (not included). We also have an A96010-kit which in addition to the part# A96010 also includes a speaker and two cable connectors to connect the unit to a power supply (not included) and the speaker. The record/play time is determined by the 52K resistor. If you change it to 89K you will get 30 seconds but at a reduced sampling rate. Operating current 25mA. Standby current 10 uA. Size: 34 x 23 x 11 mm. The module comes supplied as you see it in the photo.

This is a kit which includes the following items:
  • 1 x A96010 voice recording module (20 second message)
  • 2 x Connector cable to connect the voice recorder to a speaker and power source.
  • 1 x 1watt 3inch 8ohm Speaker
  • (You will need to connect the connector cables to the speaker and a power supply preferably by soldering)

Not included:
  • 1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.
Read More
  Partially Assembled  
  A96010-kit  
  38  
Quantity:  

40 Second Voice Recorder/Playback Module (A93010A)
tn_a93010a_general.png
 (Out of Stock)The small size is because the IC is in Chip-on-board form. One button is pushed down to record the message through the on-board electret microphone; A LED turns on during this time. The other button just has to be momentarily pressed to replay the message. A second momentary press during playback will stop the playback. Sampling rate is 12KHz. All you have to add is the speaker (not included) and 5V DC power (not included). We also have an A93010A-kit which in addition to the part# A93010A also includes a speaker and two cable connectors to connect the unit to a power supply (not included) and the speaker. Operating current 25mA. Standby current 10 uA. Size: 34 x 23 x 11 mm. The module comes supplied as you see it in the photo. 

OPTIONAL ITEMS (Not included):
  • 2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
  • 1 x (PB244) Speaker
  • 1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.
Read More
  Assembled and Tested  
  A93010A  
  0  
Quantity:  

Voice Recording Module 2 x 20sec Sections
Click here for detailed specs.
 (Out of Stock)CLOSEOUT ITEM - WHILE STOCK LASTS.

Description: The A96020 voice recording module offers true single chip solid state storage capability and requires no software or micro-controller support. It provides high quality recording and playback with dual 20 second message. Sampling rate is 3.2K. Size: 34 x 23 x 11 mm. All you need to do is add a speaker (not included) and 5V DC Power (not included).

Features:
  • Non volatile flash memory technology
  • No battery back up required
  • User friendly, easy to operate
  • Slide switch for record or play back
  • Separate key to trigger message 1 or 2
  • Low power consumption
  • LED to indicate recording and playback
  • Built-in condenser mic
  • Automatic power down
  • 5-6V Operation.

OPTIONAL ITEMS (Not included):

  • 2 x (BB089) connector cable to connect the voice recorder to a speaker and power source.
  • 1 x (PB244) Speaker
  • 1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D cells. See our battery holders.
Read More
  Assembled and Tested  
  A96020  
  0  
Quantity:  

A96020 Kit (A96020 with wires and speaker included)
Click here for detailed specs.
 (Out of Stock)CLOSEOUT ITEM - WHILE STOCK LASTS.

Description:
The A96020 voice recording module offers true single chip solid state storage capability and requires no software or micro-controller support. It provides high quality recording and playback with dual 20 second message. Sampling rate is 3.2K. Size: 34 x 23 x 11 mm. All you need to do is add a 5V DC Power supply (not included).

Features:
  • Non volatile flash memory technology
  • No battery back up required
  • User friendly, easy to operate
  • Slide switch for record or play back
  • Separate key to trigger message 1 or 2
  • Low power consumption
  • LED to indicate recording and playback
  • Built-in condenser mic
  • Automatic power down
  • 5-6V Operation.
Not Included:
  • 1 x Battery holder that can hold either 4 x AAA or 4 x AA or 4 x C or 4 x D
    cells. See our battery holders.
Read More
  Partially Assembled  
  A96020-kit  
  0  
Quantity:  

BOSS BRS35 3-1/2" Dual Cone Replacement Speaker
Click here for specs, downloads, and more pictures!
Features:
  • 3.5" dual polypropylene cone replacement speaker.
  • Read More...
Read More
  Component or Part  
  BRS35  
  1  
Quantity:  

5" Indoor/Outdoor Horn
Click here for specs, downloads, and more pictures!
Features:
  • 5" Indoor/Outdoor Horn
  • This indoor outdoor horn speaker is made of high impact white ABS plastic.
  • Completely weatherproof outdoor horn speaker, ideal for indoor or outdoor use.
  • Great for small system paging speaker application.
  • Read More...
Read More
  Component or Part  
  M-50H  
  7  
Quantity:  

10 Sec Recording Module in white case with 3 section slide switch
Click here for specs, downloads, and more pictures.
Features:
  • Ideal for plush toy, or any kind of talking toys. 
  • Message retained when batteries are removed.
  • Built-in microphone and LED recording indicator.
  • Message is retained when batteries are removed.
  • 40mm (1.6") Mylar speaker
  • Sound output of more than 85dB at 10cm (3.9") distance (surrounding at 60dB).

Operation:
Record: Slide the switch to the "REC" position. Press and hold the top of the housing. While the LED recording indicator is on, speak into the built-in microphone about 8-10 cm away with a normal speaking voice. Release the top to end recording. (Recording automatically stops when memory is full.)
Play: Slide the switch to the "PLAY" position, and press the top of the housing to play.
Read More
  Assembled and Tested  
  BRM06N  
  5,721  
Quantity:  

Recording Module 20 Second - Card Type
Click here for specs, downloads, and more pictures.
Description: 20 second card type recording unit. This module can be pasted (self-adhesive backing) into birthday cards, Christmas cards etc. When the card is opened your message will be played. You can record your own custom 20 second message with the built in microphone. The module is pre wired with a speaker and battery. All that is left for you to do is to record a message, past the module in your card and remove the little plastic tubing from the metal strip that protects the battery from running down when shipped from the factory.

Product Information:
  • Description: 20 second recording card module
  • Size:Length : 105mm, Width : 65mm, Height: 6.4mm(4.1"x 2.6" x 0.25")
  • Accessories: Battery Insulator, Battery G10 3pcs, Speaker 40mm (1.6")
  • Function: Record & Play back
  • Operation: Record : Press switch. Play back : Open the card.
  • Length of record: 20 seconds
Read More
  Assembled and Tested  
  CT94R  
  167  
Quantity:  

40 Second Non-Volatile Multi Message Recorder Kit
Click here for detailed specs.
 (Out of Stock)
Description: Non-volatile multi message recorder using ISD chips. Just change one resistor for longer duration. Standalone operation using just six onboard bottons. Record via built-in microphone or external line in. Speaker and line out connector. SPI interface. SPI mode allows full control of the chip via the serial interface. This includes random access to any location inside the memory array by specifying the start and end address. SPI mode also allows access to an internal register for configuration of audio paths, inputs, outputs and mixing. 

8-24 VDC. PCB Dimensions: 2.75" x 2"

Please Note:
Speaker not included.
Read More
  Kit - Basic Soldering Required  
  CPS188  
  0  
Quantity:  

120 Second Non-Volatile Multi Message Recorder Kit
Click here for detailed specs.
Description: Non-volatile multi message recorder using ISD chips. Just change one resistor for longer duration. Standalone operation using just six onboard bottons. Record via built-in microphone or external line in. Speaker and line out connector. SPI interface. SPI mode allows full control of the chip via the serial interface. This includes random access to any location inside the memory array by specifying the start and end address. SPI mode also allows access to an internal register for configuration of audio paths, inputs, outputs and mixing.
8-24 VDC. PCB Dimensions: 2.75" x 2"

Please Note: Speaker not included.
Read More
  Kit - Basic Soldering Required  
  CPS189  
  3  
Quantity:  

Extended record / playback module (8 minutes) (kit)
Click here for specs, downloads, and more pictures!
Description: The K8094 allows you to record and play messages of up to 8 minutes long. Recording speed is continuously adjustable so that you can choose a perfect compromise between duration and sound quality. It also allows you to generate funny sound effects. Messages are retained in memory at power loss. The unit comes complete with microphone, line level in- and output and an output for a small speaker. Applications: Play messages in musea, stores, interactive installations, scale models, toys, as doorbell, gadget, etc…

Features:

  • record duration:
    • standard quality: 8 minutes
    • High quality: 2 minutes 40s.
  • built-in microphone
  • line level in- and output
  • pushbutton control (suited for open collector control)
Read More
  Kit - Basic Soldering Required  
  K8094  
  4  
Quantity:  

2pin connector cable (8 inch)
tn_bb089.jpg
2pin connector cable (8 inch)
Read More
Quantity:  

Speaker Round 3 inch 8 ohm 1 watt
tn_pb244_general.png
Specifications:
  • Diameter: 76mm (3 inch)
  • 1 Watt
  • 8 Ohm
Read More
Quantity:  

BATTERY HOLDER FOR 4 x AA-CELL (WITH SNAP TERMINALS)
tn_bh341b.jpg
Specifications:
with snap terminals
(BH341B)
Read More
  Component or Part  
  BH341B  
  1  
Quantity:  

Battery clip for 9V PP3 Battery
tn_jb038.jpg
Specifications:

I-type
low-cost
(SNAP9V)
Read More
  Component or Part  
  SNAP9V  
  90  
Quantity:  

KC7783R PIR Detector Module (Low cost version) (Assembled and tested)
Click here for detailed specs.
Mechanical and electrical specs is the same as the KC7783 except for a lower cost IC (KC778B IC) package used in this KC7783R.


RoHS Compliant: YES.
Read More
  Component or Part  
  BB054  
  497  
Quantity:  

KC7786 PIR Sensor Module 12v (3pin .1in)
Click here for detailed specs.
Description: This is a fully assembled and tested miniature PIR module (KC7786 with KC778B COB IC) with only 3 connections: Power, Ground & Output (3 pin terminal of standard 0.1 inch pitch). Rated for 12VDC input power. Uses RE200B PIR sensor. Output is an active high pulse of approx. 0.5 seconds and remains active as long as there is motion. Range up to 10 feet. PCB size: 27mm x 27mm
Read More
  Component or Part  
  BB043  
  59  
Quantity:  

Melody Card X-mas Tunes (Jingle Bells + Santa Claus + We Wish You a Merry X'mas) COB Module
Click here for detailed specs.
 (Out of Stock)Complete melody card unit- 'Three Christmas Carols' (Jingle Bells + Santa Claus + We Wish You a Merry X'mas) Melody IC COB, battery and piezo all ready to play. As found in Christmas cards and books which play when you open the page. Self-adhesive backing. Tune repeats continuously while power is connected. Total of 128 notes. Cmos LSI. (SG14)
Read More
  Assembled and Tested  
  SG14  
  0  
Quantity:  

BATTERY HOLDER FOR 4 x AAA-CELL (WITH SOLDER TAGS)
Click here for specs, downloads &/or more pictures...
Specifications:
  • with solder tags (BH443D)
Read More
  Component or Part  
  BH443D  
  16  
Quantity:  

Melody Card Happy Birthday COB Module
Click here for detailed specs.
Complete Card Melody Unit- 'Happy Birthday' Melody IC COB, battery and piezo all ready to play. As found in Christmas cards and books which play when you open the page. Self-adhesive backing. Tune repeats continuously while power is connected. Total of 128 notes. Cmos LSI.
Read More
  Assembled and Tested  
  SG13  
  975  
Quantity: